No Detail Found!

Power plant reliability issues and wear monitoring in aircraft piston engines. Part i: engine wear and tbo real-time extension

Author(s)
Luca Piancastelli Department of Industrial Engineering, Alma Mater Studiorum University of Bologna,Viale Risorgimento, Bologna,Italy
Eugenio Pezzuti Università di Roma "Tor Vergata", Dip. di Ingegneria dell'Impresa "Mario Lucertini”,Via del Politecnico, Roma,Italy
Stefano Cassani MultiProjecta,Via Casola Canina, Imola (BO),Italy
Abstract
This paper introduces a method to prepare an engine for very long flights without maintenance. It also gives criteria to estimate time between overhaul by using the sensor data to have an estimation of the engine condition. In-flight refueling has introduced new challenges to UAV (Unmanned Aerial Vehicle) propulsion systems. It is now possible to run continuously an UAV without landing for long periods. For this task, it is necessary to carry a quantity of lubricant sufficient for at least one month (approximately 800h). For extremely long flights, diesel piston engines are better than spark ignition ones due to extremely low fuel consumption. A selection in the assembly line individuates those engines that are suitable for long endurance flight. This is possible because automotive engines are manufactured in thousands per day and many quality controls take place in the assembly process. Moreover, mass produced automotive engines pass several tests during the assembly process including a very short run. The results of these tests are useful for an initial selection. Then, a 25-hour trial with a very thin lubricant is sufficient to forecast the oil consumption up to 1,000 hours. The 25 hours run corresponds to the time necessary to stabilize the oil consumption rate. In addition, during the 25 hours run also the electronic infancy failures are detected. In modern engines, the electronic on board diagnosis, the full redundancy of vital sensors, electronic control units and batteries/generators, make it possible to fly safely without emergencies with random electronic failures of components and wiring. Another major requirement is to forecast the engine failure or an unacceptable deterioration in terms of mechanical performance. This paper introduced a method to evaluate the state of wear of the engine starting from a digital monitoring system. A wear model of the engine based on the real duty cycle is proposed. It is then possible to prolong the life of the engine and to increase the time between overhaul. It is also possible schedule the overhaul operation.
Publication Details
Page(s) 806-814
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 17, Issue: 7, Year: 2022

Request the full text from PASTIC

Keywords
TBO evaluation, 800h flight, piston engine, Aircraft
References
AA. VV. .2018 .Asset s/Oil-consumption-and-oil-loss_51747. (accessed on 26 February, : .
Del Prete A.,osservatorio UnipolSai Prete A. .2017 .(data retrieved from car black boxes by Unipolsai Insurance Company. Resto Del Carlino ed. Bologna, 21 November, : .
Peng L.,Tusinean A.,Hofbauer P.,Deylami K.,Army U.S.,TARDEC U.S.,Rd Mile .2018 .Development of a Compact and Efficient Truck APU. pdf (accessed on 28 March, : 48397-5000.
Wilkins D. J. .2018 .The Bathtub Curve and Product Failure Behavior Part One - The Bathtub Curve, Infant Mortality. htm (accessed on 27 February, : .
AA. VV. .2018 .In-Process Testing for Engine Manufacturing using Signature Analysis. pdf (accessed on 27 February, : 01-12.
Facts About Engine AA. VV. 2018. Hard,- AA. VV. 2018. Hard .2018 .. (accessed on 27 February, : .
AA. VV. .2003 .. , : .
Piancastelli L.,Frizziero L.,Pezzuti E.,Ipswich P.O. Box 682 .1819 .Aircraft diesel engines controlled by fuzzy logic. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(1) : 30-34.
Piancastelli L.,Frizziero L.,Morganti E.,Canaparo A. .2012 .Fuzzy control system for aircraft diesel engines. International Journal of Heat and Technology, ISSN 0392-8764, (1) : 131-135.
Piancastelli L.,Frizziero L.,Rocchi I. .2012 .A. Feasible optimum design of a turbocompound Diesel Brayton cycle for diesel-turbo-fan aircraft propulsion. International Journal of Heat and Technology, ISSN 0392-8764, (2) : 121-126.
Piancastelli L.,Frizziero L.,Daidzic N. E.,Rocchi I.,Ipswich P.O. Box 682 .2013 .Analysis of automotive diesel conversions with KERS for future aerospace applications. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN 0392-8764, (1) : 807-818.
Piancastelli L.,Frizziero L.,Pezzuti E.,Ipswich P.O. Box 682 .1819 .Kers applications to aerospace diesel propulsion. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(5) : 32-36.
Dannenhoffer R. F.,Grumman R. F. .1981 .Engine Duty Cycle Estimation for Conceptual Design Aircraft. Joint Propulsion Conference. Anniversary. July 27-29, : .
Ellerman J.,Rohrle M.,Schelling H. .1981 .Oil Consumption and Blowby of Truck Diesel EnginesTest Bench Results. , 810937 : 37-45.
Ishizuki Y.,Soto F.,Takase K. .1981 .Effect of Cylinder Liner Wear on Oil Consumption in Heavy Duty Diesel Engines. , 810931(1) : 6.
Palmgren A. .1924 .Die Lebensdauer von Kugelgen. , 68 : 339-340.
Miner M.A. .1945 .Cumulative Damage in Fatigue. Journal of Applied Mechanics, 67(A159) : 223-226.
Piancastelli L.,Frizziero L.,Morganti E.,Canaparo A. .2012 .Method for evaluating the durability of aircraft piston engines. Walailak Journal of Science and Technology, ISSN 1686-3933, (4) : 425-431.
Archard J.F. .1953 .Contact and Rubbing of Flat Surface, J. , 24(8) : 981-988.
Binner T.,Reister H.,Ernst P.,Weidmann J. .2018 .Aspects of Underhood Thermal Analyses. pdf (accessed on 30 March, : .
Caligiana G.,Liverani A.,Francia D.,Frizziero L.,Donnici G. .2017 .Integrating QFD and TRIZ for innovative design. Journal of Advanced Mechanical Design, Systems and Manufacturing, 11(2) : .
Francia D.,Caligiana G.,Liverani A.,Frizziero L.,Donnici G. .2018 .Printer CAD: a QFD and TRIZ integrated design solution for large size open moulding manufacturing. 1st February, 12(1) : 81-94.
0

Citations

0

Downloads

12

Views