No Detail Found!

Manufacturing and development of MgB2 superconducting wire through hot rolling process

Author(s)
Satrio Herbirowo Department of Metallurgical and Material Engineering, Universitas Indonesia, Indonesia;Research Center for Advanced Materials, National Research and Innovation Agency, South Tangerang, Banten, Indonesia
Alex S. Purba Department of Physics, Sumatera Utara University,,Indonesia
Vinda Puspasari Research Center for Advanced Materials, National Research and Innovation Agency,South Tangerang, Banten,Indonesia
Perdinan Sinuhaji Department of Physics, Sumatera Utara University,,Indonesia
Nofrijon Sofyan Department of Metallurgical and Material Engineering,Universitas Indonesia,Indonesia
Akhmad Herman Yuwono Department of Metallurgical and Material Engineering,Universitas Indonesia,Indonesia
Agung Imaduddin Research Center for Advanced Materials, National Research and Innovation Agency,South Tangerang, Banten,Indonesia
Abstract
In this study, the synthesis and manufacture of MgB2/SS 316L Superconducting Wire by In-Situ method through hot rolling with a variety of sintering temperatures and holding time with the novelty of the SS316 sheath and hot rolling method were carried out to maintain the size reduction results without stress concentration and minimal defects. MgB2 is a superconducting material with a critical temperature of ~39 K. Hot rolling process with a variety of sintering temperatures and holding time was carried out to observe its effect on the superconductivity characteristics of MgB2. The process of synthesis and sample preparation begins by measuring and cutting the SS3I6L tube and weighing the raw materials, which were Mg and B powders with a ratio of 1:2 according to stoichiometric calculations. The material was then grounded for 2 hours using an agate mortar and then put into an SS 316L stainless steel tube where it was completely compacted. Then, the sintering process was carried out using a muffle furnace with variations in sintering temperature of 780°C, 800°C, 820°C, and holding time for 1 hour and 3 hours. After that, a hot rolling process was carried out on each sample with a temperature of 300°C. The samples were characterized by XRD, Cryogenic Magnet and SEM-EDS. The identification through XRD showed that the phases formed were MgB2, MgO, Fe. The Cryogenic Magnet test showed superconductivity at a sintered temperature of 800°C and 820°C with a holding time of 1 hour, where for a sintered temperature of 800°C, it has a Tconset of 39.55 K and a Tczero of 34.69 K while at sintered temperature of 820°C the TcOnset is 38, 44 K TcZero is 31.30 K.However, in the MgB2 sample, the sintered temperature of 780°C with a holding time of 1 hour did not show superconductivity properties. Meanwhile, sintering temperature variation of 780°C, 800°C, 820°C with a holding time of 3 hours showed superconductivity properties, namely the appearance of Tconset and Tczero in each sample. The morphological structure and elemental composition were seen through SEM-EDS, where the surface morphology had a hexagonal grain shape. As the sintering temperature and holding time increase, the surface morphology of the grains becomes denser and more regular so that the porosity is smaller.
Publication Details
Page(s) 727-732
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 17, Issue: 7, Year: 2022

Request the full text from PASTIC

Keywords
hot rolling, stainless steel SS 316L, In-Situ Powder in Tube (PIT), magnesium diboride (MgB2), superconductivity, sintering temperature and holding time
References
Amiruddin A.,Lubis F. A. .2018 .Analisa Pengujian Lelah Material Tembaga Dengan Menggunakan Rotary Bending Fatigue Machine. Jurnal Ilmiah “MEKANIK” Teknik Mesin TM, 4(2) : 93-99.
Zhao Q.,Liu Y.,Cai Q. .2012 .Influence of Ni addition on the process of phase formation in MgB2 bulk. Appl. Phys. A Mater. Sci. Process, 107(4) : 877-883.
Yudanto S. W.,Imaduddin A.,Siswayanti B. dan Herbirowo S. .2021 .Analisis Hambat Jenis Penambahan Nano SiC pada Superkonduktor MgB2 Tanpa Perlakuan Panas. Prosiding Seminar Material Metalurgi LIPI; Tangerang, 28 Februari, : 287-292.
Nagamatsu J.,Nakagawa N.,Muranaka T.,Zenitani Y.,Akimitsu J. .2001 .Superconductivity at 39 K in Magnesium Diboride. Nature, 410 : 63-64.
Erhan A,Measurements Magnetic .2013 .Study of MgB2 Phase Formation by Using XRD, SEM, Thermal. , : .
Akdogan .2017 .Use of Phous Boron and Amourphous Nano Boron Powder Mixture in Fabrication of Long In- situ MgB2/ Fe Wires. , : .
Herbirowo S.,Sofyan N.,Imaduddin A. .1826 .Properties of carbon nanotubes - doped Fe-sheath MgB2 for superconducting wires. AIP Conf. Proc, : .
Varghese N.,Vinod K.,Abhilash Kumar R. G.,Syamaprasad U.,Sundaresan A. .2007 .Influence of reactivity of sheath materials with Mg/B on superconducting properties of MgB2. Journal of Applied Physics, 102(4) : 0-4.
Siregar DD .2016 .Pengaruh Penambahan Mg Pada Perlakuan Panas Superkonduktor MgB2. , : .
Suo H. L.,Musolino N.,Beneduce C.,Toulemonde P.,Lezza P.,Fl R. .2003 .Superconducting properties of MgB2 tapes and wires. , 385 : 286-305.
I. Salsabila ,Jalil Z. .2018 .Pengaruh Suhu Sintering dan Komposisi Air Dalam Suspensi Terhadap Ukuran Kristal Hidroksiapatit Berbasis Tulang Sapi Aceh. Jurnal Aceh Phys. Soc., jilid 7, tidak. 3, : 157-161.
Zhao Q.,Liu Y.,Cai Q. .2012 .Influence of Ni addition on the process of phase formation in MgB2 bulk. Appl. Phys. A Mater. Sci. Process, 107(4) : 877-883.
0

Citations

0

Downloads

9

Views