No Detail Found!

A statistical analysis of diesel piezo injector fuel injection timing and duration measured with a photosensor

Author(s)
Jun Pil Choi Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology,Seoul,Korea
Choong Hoon Lee Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology,Seoul,Korea
Abstract
When a piezo-type diesel injector was driven using various current patterns, the fuel injection start and stop timings were measured with a photosensor. The photosensor was positioned as close as possible to the piezo injector nozzle hole to accurately capture the start and stop timings. The charge currents for driving the piezo injector were controlled in nine different patterns. A peak-and-hold current waveform was generated using a microcontroller with pulse width modulation (PWM) control. The fuel injection duration was set to 1.0 ms. The common rail pressure was regulated in five cases: 30 MPa, 50 MPa, 70 MPa, 90 MPa, and 120 MPa. To analyze the uncertainty in fuel injection start timing and duration, measurements were repeated 33 times for each experimental condition. Among the nine current patterns used to drive the piezo injector, the pattern with the smallest variations in fuel injection start timing and duration was investigated. It was found that the peak current value had a significant impact on the variations in both injection start timing and duration.
Publication Details
Page(s) 919-926
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 20, Issue: 13, Year: 2025

Request the full text from PASTIC

Keywords
end of injection, fuel injection timing, peak and hold, fuel injection duration, start of injection, piezo injector
References
d'Ambrosio S.,Mancarella A.,Manelli A.,Mittica A.,Hardy G. .2021 .Experimental Analysis on the Effects of Multiple Injection Strategies on Pollutant Emissions, Combustion Noise, and Fuel Consumption in a Premixed Charge Compression Ignition Engine. SAE Int. J. Engines, 14 : 611-630.
Olmeda P.,Martin J.,Garcia A.,Villalta D.,Warey A.,Domenech V. .2017 .A Combination of Swirl Ratio and Injection Strategy to Increase Engine Efficiency. SAE Int. J. Engines, 10 : 1204-1216.
Piano A.,Boccardo G.,Millo F.,Cavicchi A.,Postrioti L.,Pesce F. C. .2017 .Experimental and Numerical Assessment of Multi-Event Injection Strategies in a Solenoid Common-Rail Injector. SAE Int. J. Engines, 10 : 2129-2140.
Biswas S.,Bakshi M.,G. M.,Mukhopadhyay A. .2016 .Experimental Investigation on the Effect of Two Different Multiple Injection Strategies on Emissions, Combustion Noise, and Performance of an Automotive CRDI Engine. , 01 : .
Zhou Q.,Lucchini T.,G. D'Errico N.,Maes B.,Somers X. C.,Lu X. C. .2020 .Computational Modeling of Diesel Spray Combustion with Multiple Injections, SAE Int. J. Adv. & Curr. Prac. in Mobility, 2 : 2839-2858.
Park C. W.,Kook S. H.,Bae C. S. .2004 .Effects of Multiple Injections in a HSDI Diesel Engine Equipped with Common Rail Injection System. , 01 : .
Busch S.,Zha K.,Miles P.,Warey A.,Pesce F.,Peterson R.,Vassallo A. .2015 .Experimental and Numerical Investigations of Close-Coupled Pilot Injections to Reduce Combustion Noise in a SmallBore Diesel Engine. SAE Int. J. Engines, 8 : 660-678.
Mobasheri R.,Peng Z. .2012 .Investigation of Pilot and Multiple Injection Parameters on Mixture Formation and Combustion Characteristics in a Heavy Duty DI-Diesel Engine. , 01 : .
Coppo M.,Dongiovanni C.,Negri C. .2004 .Numerical Analysis, Experimental investigation of a common rail type diesel injector. ASME Trans. J. Eng. Gas Turbines Power, 126 : 874-885.
Coppo M.,Dongiovanni C.,Negri C. .2007 .A linear optical sensor for measuring needle displacement in common rail diesel injectors. Sensors and Actuators A, 134 : 366-373.
Amirante R.,Catalano L. A.,Coratella C. .2013 .A New Optical Sensor for the Measurement of the Displacement of the Needle in a Common Rail Injector. , 24 : .
Volkswagen A. G. .1999 .1.9 ltr-TDI-Industrial Engine Technical instruction. , : .
Zhang X.,Palazzolo A.,Kweon C. B.,Tucker R.,Kascak A. .2014 .Direct Fuel Injector Temporal Measurements. , 01 : .
Park S. J.,Lee C. H. .2023 .A comparative study of the detection of the fuel injection start and stop timing of a diesel injector using a photo sensor, a shock sensor, and a needle lift sensor. Journal of Mechanical Science and Technology, 37 : 477-485.
SAE J1832 .2016 .Surface vehicle recommended practice: Low-pressure gasoline fuel injector. , : .
Baek J. H.,Lee C. H. .2024 .Fuel injection rate variation of a piezoelectric injector according to the charge current patterns. Journal of Mechanical Science and Technology, 38 : 453-461.
Lee C. H.,Lee Y. J. .2018 .Development of Diesel Piezo Injector Driver using Microcontrollers. ARPN Journal of Engineering and Applied Sciences, 13 : 4860-4865.
.2023 .OMRON, Slot-type Photomicrosensor with Cable EE-. , : .
0

Citations

0

Downloads

23

Views