No Detail Found!

Optimization of the design of an external gear pump casing and efficiency through structural finite element analysis and using response surface methodology

Author(s)
N. Habi Laboratory of Mechanics, Physics and Mathematical Modelling (LMP2M), University of Medea, Algeria.
R. Rebhi Laboratory of Renewable Energies and Materials-LERM, University of Medea,,Algeria
A. Abdellah El-Hadj Laboratory of Mechanics, Physics and Mathematical Modelling (LMP2M), University of Medea, Algeria.
M. Bachene Laboratory of Mechanics, Physics and Mathematical Modelling (LMP2M), University of Medea, Algeria.
Shayfull Zamree Abd Rahim Universiti Malaysia Perlis (UniMAP), Faculty of Mechanical Engineering Technology,Arau, Perlis,Malaysia
Abstract
In this study, we present an improvement in the external gear pump casing by reducing its weight, aiming to minimize the material used in manufacturing while maintaining casing stiffness and increasing the efficiency to mass ratio. The finite element method (FEM) was employed using ANSYS Workbench to analyze the pump casing under operating pressure, allowing for the calculation of stress and deformation. The geometric model of the pump casing was created using SolidWorks, where we linked its dimensions to a single reference parameter using the equation tool. This approach facilitated the optimization process without altering the original design. The optimization analysis was conducted using the Response Surface Methodology (RSM), based on the results obtained. The study led to an optimal design that balances lightweight characteristics with structural strength. A weight reduction of 9.5% was achieved compared to the original design, with a maximum recorded deformation of 0.031 mm and a maximum stress of 127 MPa, resulting in a safety factor of 3, demonstrating the strength and robustness of the optimal design. Additionally, the efficiency to mass ratio was calculated for both the original and optimized designs. The optimized design achieved a value of 8.8, compared to 7.9 for the original, highlighting the enhanced performance and efficiency of the optimal design.
Publication Details
Page(s) 789-800
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 20, Issue: 12, Year: 2025

Request the full text from PASTIC

Keywords
efficiency to mass ratio, external gear pumps casing, Optimization, Finite Element Analysis, response surface methodology
References
Yang H. Y.,Pan M. .2015 .Engineering research in fluid power: a review. Journal of Zhejiang UniversityScience A, 16(6) : 427-442.
Ferrari C.,Morselli S.,Miccoli G.,Hamiche K. .2024 .Integrated CFD-FEM approach for external gear. , : .
Kattimani K. D.,Tavildar R. K K. D.,Kakamari P. P. .2016 .Finite element analysis and optimization of external gear pump. Jetir, 3 : 119-126.
Gulati S.,Vacca A.,Rigosi M. .2016 .A general method to determine the optimal profile of porting grooves in positive displacement machines: the case of external gear machines. , : .
Cieślicki R.,Karpenko M. .2022 .An investigation of the impact of pump deformations on circumferential gap height as a factor influencing volumetric efficiency of external gear pumps. Transport, 37(6) : 373-382.
Kollek W.,Osiński P.,Warzyńska U. .2017 .The influence of gear micropump body asymmetry on stress distribution. Polish Maritime Research, 24(93) : 60-65.
Cieślicki R. .2018 .Numerical model of an external gear pump and its validation. Karliński J. and Osiński P, : 96-103.
Guo F. .2020 .September. Finite element analysis and optimization of CBY-100 gear pump body. In Journal of Physics: Conference Series, 1622(1) : 012116.
Ghionea I. G. .2022 .Applied Methodology for Designing and Calculating a Family of Spur Gear Pumps. , 15(12) : 4266.
Rodionov L.,Stryczek J.,Rekadze P.,Stryczek P.,Gafurov S.,Prokofiev A.,Shakhmatov E. .2021 .Challenges in design process of gear micropump from plastics. Archives of Civil and Mechanical Engineering, 21(1) : 34.
Zharkevich O.,Nikonova T.,Gierz Ł.,Berg A.,Berg A.,Zhunuspekov D.,Fryczyński K. .2023 .Parametric optimization of a new gear pump casing based on weight using a finite element method. Applied Sciences, 13(22) : 12154.
Ozsoy M.,Kurnaz C. .2017 .An optimization study of a hydraulic gear pump cover with finite element method. Acta Physica Polonica A, 132(3) : 944-948.
Kollek W.,Radziwanowska U. .2014 .The modernization of gear micropump casing with the use of finite element method. IMPACT: International Journal of Research in Engineering & Technology (IMPACT: IJRET), 2(7) : 69-76.
Kollek W.,Radziwanowska U. .2015 .Energetic efficiency of gear micropumps. Archives of Civil and Mechanical Engineering, 15(1) : 109-115.
Yanikören M. .2025 .Experimental investigation of the performance and energy consumption efficiency of elliptical gear hydraulic pump and evaluation by Taguchi method. Engineering Science and Technology, an International Journal, 62 : 101941.
Okouzi A. S.,Ibhadode A. O. A.,Obanor A. I. .2021 .Response surface methodology (RSM) optimization of the batch process in a rectangular passive greenhouse dryer. International Journal of Engineering Research in Africa. 56, : 145-161.
0

Citations

0

Downloads

25

Views