No Detail Found!

Cutting of 316L stainless steel for metal mesh implant using co2 laser cutting: analysis and optimization

Author(s)
Gunawan Mechanical Engineering Graduate Study Program, Faculty of Engineering,Universitas Sumatera Utara, Jalan Almamater, Kampus USU, Medan,Indonesia
Armansyah Ginting Department of Mechanical Engineering, Faculty of Engineering,Universitas Sumatera Utara, Jalan Almamater, Kampus USU, Medan,Indonesia
Suprianto Department of Mechanical Engineering, Faculty of Engineering,Universitas Sumatera Utara, Jalan Almamater, Kampus USU, Medan,Indonesia
Abstract
This study investigates the effects of CO2 laser cutting parameters on the quality of 316L stainless steel used for metal mesh implants. A Taguchi L9 orthogonal array was employed to design the experiments with three factors: laser power (100-200 W), cutting speed (50-150 mm/min), and gas pressure (3-9 bar). The dimensions (Dim) and heat-affected zone (HAZ) of the cuts were analyzed using both Taguchi and Hybrid Taguchi-Grey Relational Analysis (T-GRA) methods. Results from Taguchi analysis identified the optimal parameters for minimizing Dim as 100 W, 100 mm/min, and 6 bar, and for HAZ as 100 W, 50 mm/min, and 6 bar. ANOVA indicated that laser power significantly influenced both Dim (41.11%) and HAZ (28.10%). T-GRA optimization predicted the optimal parameters as 200 W, 50 mm/min, and 3 bar, confirmed through validation experiments with a Grey Relational Grade (GRG) of 0.969. The study concludes that laser power is the most critical parameter, followed by gas pressure and cutting speed, providing a comprehensive optimization strategy for laser cutting 316L stainless steel for medical implants.
Publication Details
Page(s) 1165-1172
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 19, Issue: 18, Year: 2024

Request the full text from PASTIC

Keywords
Parameter optimization, heat affected zone (HAZ), dimension, taguchi-grey relational analysis (T-GRA)
References
Romero-Resendiz L.,El-Tahawy M.,Zhang T.,Rossi M. C.,Marulanda-Cardona D. M.,Yang T. .2022 .Heterostructured stainless steel: Properties, current trends, and future perspectives. , 10 : 100691.
Dehghan-Manshadi A.,Yu P.,Dargusch M.,Qian St John D.,M. St John D. .2020 .Metal injection moulding of surgical tools, biomaterials, and medical devices: A review. Powder Technology, 01 : 189-204.
Li J.,Qin L.,Yang K.,Wang Y .2019 .Materials evolution of bone plates for internal fixation of bone fractures: A review. Journal of Materials Science & Technology, 07 : 190-208.
Ahmad M.,Javaid M.,Haleem A. .2024 .Enhancing biocompatible metal alloy fabrication for bio implants through laser-based additive manufacturing (LBAM). Biomedical Analysis, 02(1) : 73-85.
Zhang E.,Zhao X.,Hu J.,Wang R.,Fu S.,Qin G. .2021 .Antibacterial metals and alloys for potential biomedical implants. Bioactive Materials, 01(8) : 2569-2612.
Muhammad N.,Whitehead D.,Boor A.,Li L. .2010 .Comparison of dry and wet fibre laser profile cutting of thin 316L stainless steel tubes for medical device applications. Journal of Materials Processing Technology, 08(15) : 2261-2267.
Eltawahni H. A.,Hagino M.,Benyounis K. Y.,Inoue T.,Olabi A. G. .2011 .Effect of CO2 laser cutting process parameters on edge quality and operating cost of AISI316L. Optics & Laser Technology, 10(4) : 1068-1082.
Jarosz K.,Löschner P.,Niesłony P. .2016 .Effect of Cutting Speed on Surface Quality and Heataffected Zone in Laser Cutting of 316L Stainless Steel. Procedia Engineering, 06 : 155-162.
Rajesh K.,Murali Krishnam K.,Rajesh S.,Sudheer Kumar Varma N. S. .2019 .Effect of process parameters on machinability characteristics of CO2 laser process used for cutting SS-304 Stainless steels. Materials Today: Proceedings, 06 : 2065-2072.
Parthiban A.,Dhanasekaran C.,Sivaganesan S.,Sathish S. .2019 .Modeling on surface cut quality of CO2 laser cutting for Austenitic Stainless steel sheet. Materials Today: Proceedings, 07 : 823-827.
Alsaadawy M.,Dewidar M.,Said A.,Maher I.,Shehabeldeen T. A. .2024 .A comprehensive review of studying the influence of laser cutting parameters on surface and kerf quality of metals. The International Journal of Advanced Manufacturing Technology, 10(3-4) : 1039-1074.
Khatak P. .2021 .Laser cutting technique: A literature review. Materials Today: Proceedings, 08 : 2484-2489.
Parandoush P.,Hossain A. .2014 .A review of modeling and simulation of laser beam machining. International Journal of Machine Tools and Manufacture, 05 : 135-145.
Rana R. S.,Chouksey R.,Dhakad K. K.,Paliwal D. .2018 .Optimization of process parameter of Laser beam machining of high strength steels: A review. Materials Today: Proceedings. DOI:10, 06 : .
Anghel C.,Gupta K.,Jen T. C. .2019 .Analysis and optimization of surface quality of stainless steel miniature gears manufactured by CO2 laser cutting. Optik, 10 : .
Vishnu Vardhan T.,Mahender T.,Vempati S.,Balram Y. .2023 .Optimization of laser machining parameters of SS 314 using response surface methodology. Materials Today: Proceedings. DOI:10, 02 : .
Senthilkumar V.,Jayaprakash G. .2017 .Parametric investigation and modelling of hardness and surface quality in CO2 laser cutting process of AISI 314 Stainless steel. DOI: 10.14447/jnmes.v20i3.402, 20(3) : .
Senthilkumar V.,Adinarayanan A.,Jagatheesan K. .2022 .Grey Relational Analysis (GRA) for optimization of CO2 laser cutting of stainless steel. Materials Today: Proceedings, 09 : 2437-2442.
Ju-Long D. .1982 .Control problems of grey systems. Systems & Control Letters, 6911(82) : 80025-294.
Liu S.,Yang Y.,Xie N.,Forrest J. .2016 .New progress of Grey System Theory in the new millennium. Grey Systems: Theory and Application, 10(1) : 2-31.
Patil D. S.,Arakerimath R. R.,Walke P. V.,Shelke R. S. .2020 .Performance optimization of exhaust heat exchanger with internal structures by using Taguchi and grey relational analysis. ARPN Journal of Engineering and Applied Sciences, 15(3) : .
Madhava Reddy P.,Vijaya Bhaskara Reddy P.,Naresh N. .2014 .Optimization of machining parameter for turning of EN 16 steel using Grey-based Taguchi method. ARPN Journal of Engineering and Applied Sciences, 9(3) : .
Roslan A. F.,Salehuddin F.,Zain A. S. M.,Kaharudin K. E.,Ahmad I. .2020 .Comparison of L25 GRA and L25 Taguchi statistical method for optimizing 16 NM DG-FinFET on output variation. ARPN Journal of Engineering and Applied Sciences, 15(2) : .
0

Citations

2

Downloads

62

Views