No Detail Found!

Enhancement of thermal and mechanical properties of PMMA nanocomposites by adding spark plug ceramic waste

Author(s)
Wasan Ali Hussein Department of Physics, College of Science, University of Wasit, Kut, Wasit, Iraq Department of Science, College of Basic Education, Wasit University,,
Yahya M. Abbas Department of Physics, College of Science, University of Wasit, Kut, Wasit, Iraq Department of Science, College of Basic Education, Wasit University,,
Ahmed Jadah Farhan Department of Physics, College of Science, University of Wasit, Kut, Wasit, Iraq Department of Science, College of Basic Education, Wasit University,,
Abstract
In this research, poly methyl methacrylate (PMMA) resin was used as a base material and spark plug ceramic waste (CW) particles as a support material with different weight ratios (0%, 1%, 2%, 4%, 6%, 10%, 14%, and 20%) to study the thermal and mechanical properties through diffraction examination. FE-SEM surface structure images showed that the fracture surface of the (94% PMMA +6%CW) nanocomposite sample manifests a good distribution of particles at low and high levels. The result showed that the thermal conductivity (K) slightly increased until it reached the maximum value (0.6 watt/m.ºC) at the ratio (86%PMMA +14%CW). For the impact strength, it was noticed that the impact strength of PMMA increases with the increased weight ratios (1, 2, 4, 6, 10, 14, and 20%) of fine powder of ceramic waste compared with pure PMMA to reach the maximum value (6.02 kJ/mm2) at the sample (94% PMMA +6%CW) under L.C. Moreover, after 30 days of submersion in water, the PMMA reinforced with ceramic waste particles had enhanced impact strength. The shore D-number readings for all of the samples showed an increase as a result of the findings of nanocomposite compared with PMMA pure, where the sample (94% PMMA+6%CM) attained the greatest shore D numbers (87 H.NO). The compressive strength at the weight percentage (99% PMMA + 1% CW) was somewhat reduced. Then the compressive strength increased till it reached its maximum value (29.94 MPa) at the weight percentage (94% PMMA + 6% CW).
Publication Details
Page(s) 658-665
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 19, Issue: 11, Year: 2024

Request the full text from PASTIC

Keywords
thermal conductivity, Mechanical properties, spark plug ceramic waste particles, PMMA resin, and nanocomposite
References
Lu H.,Yao Y.,Huang W. M.,Leng J.,Hui D.,Nitride. Composites Part Boron,B Boron .2014 .Significantly Improving Infrared Light-Induced Shape Recovery Behavior of Shape Memory Polymeric Nanocomposite via a Synergistic Effect of Carbon Nanotube. , 62 : 256-261.
Hashemi R. .2016 .On the Overall Viscoelastic Behavior of Graphene/Polymer Nanocomposites with Imperfect Interface. International Journal of Engineering Science, 105 : 38-55.
Cano M. .2013 .Improving the Mechanical Properties of Graphene Oxide Based Materials by Covalent Attachment of Polymer Chains. Carbon, 52 : 363-371.
Mutiso R. M.,Winey K. I. .2015 .Electrical Properties of Polymer Nanocomposites Containing Rod-Like Nanofillers. Progress in Polymer Science, 40 : 63-84.
Yuan B.,Properties Mechanical .2014 .Preparation of Functionalized Graphene Oxide/Polypropylene Nanocomposite with Significantly Improved Thermal Stability and Studies on the Crystallization Behavior. , 237 : 411-420.
Yousefi N. .2014 .Highly Aligned Graphene/ Polymer Nanocomposites with Excellent Dielectric Properties for High­Performance Electromagnetic Interference Shielding. Advanced Materials, 26 : 5480-5487.
Hong N. .2014 .Co-Precipitation Synthesis of Reduced Graphene Oxide/NiAl-Layered Double Hydroxide Hybrid and its Application in Flame Retarding Poly (Methyl Methacrylate). Materials Research Bulletin, 49 : 657-664.
Chakraborty S.,Kumar M.,Suresh K.,Pugazhenthi G. .2016 .Investigation of Structural, Rheological, and Thermal Properties of PMMA/ONiAl LDH Nanocomposites Synthesized via Solvent Blending Method: Effect of LDH Loading. Chinese Journal of Polymer Science, 34 : 739-754.
Atta A. M.,Elnagdy S. I.,Abdel-Raouf S. I. .2005 .. Polym. Res, 12 : 373.
Selly J. UPE,Mark H. F. .1988 .Encyclopedia of Polymer Science and Engineering. , 12 : 256-290.
Kramer H. .1972 .. Ullmanns Encyclopedia of Industrial Chemistry. Weinheim, A21, : 217.
Gong Y.,Shen R. X.,Li H. Q.,PRC H. Q. .2002 .Concrete. J. Wuhan Univ. Technol, 29(4) : 58-60.
Xu S. L.,Li H. D. .2008 .A review of the development of research and application of ultrahigh toughness cementitious composites. China Civil. Eng. J, 41(6) : 45-60.
Intisar J.,Ismail J. .2014 .The Effect of Silanized Alumina Nano-Fillers Addition on Some Physical and Mechanical Properties of Heat Cured Polymethyl Methacrylate Denture Base Material J. Bagh Coll Dentistry, 26(2) : 18-23.
Hafsa Naznin A.,Abul K.,Mallik K.,Khandker S. Hossain B.,Md Shahruzzaman A.,Papia Haque A.,Mohammed Mizanur Haque A.,GO Haque A.,Published by Elsevier B.V. .2021 .Enhancement of thermal and mechanical properties of PMMA composites by incorporating mesoporous micro-silica and. Results in Materials 11, : 100203.
Jaffer Harith I. .2020 .Investigation of the Thermal Conductivity of Binary Polymer Blends. IOP Conf. Ser.: Mater. Sci. Eng, 10 : 1757.
Fadhil Abbas,Essa Abbas,Jerjack Najlaa .2014 .Preparation and study Impact and Hardness Strength for Gravel Nano Particles /Polyester Composites. J. Thi-Qar Sci. 4, (4) : .
Dewimille B.,Bunsell A. .1983 .. , 14(1) : 35-40.
Gupta R. K.,Kim K. J. .2010 .(Polymer Nanocomposites Handbook) Taylor. , : .
Safarabadi M.,Khansari N. M.,Rezaei A. .2014 .An experimental investigation of HA/AL2o3 nanoparticles on mechanical properties of restoration materials. Eng, 4(3) : 173-182.
Raja R. S.,Manisekar K.,Manikandan V. .2013 .Effect of fly ash filler size on mechanical properties of polymer matrix composites. Int. J. Mining, Metall. Mech. Eng, 1(1) : 34-38.
0

Citations

0

Downloads

81

Views