No Detail Found!

Augmentation of Fatigue and Tensile Strength of AA-6061 Processed through Equal Channel Angular Pressing.

Author(s)
Nazeer Ahmed Anjum Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
SHAHID MEHMOOD Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
Waqas Anwar National Engineering and Scientific Commission of Pakistan
Zahid Salman Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
Saeed Badshah International Islamic University (IIU), Islamabad, Pakistan
Abstract
ECAP (Equal Channel Angular Pressing) is a technique used to enhance the strength of material by grain refinement. In this research, an aerospace grade aluminum alloy-6061 is investigated. The specimens were pressed through ECAP die channels, intersecting each other at an angle of 90oC where a shear plane of 45oC was developed, that results grains refinement. Fatigue strengths and CGR (Crack Growth Rate) for the stress ratio R 0.7 and 0.1 are found and compared with the as-received material.It was observed that the CGR is slower at stress ratio R=0.1, as compared to stress ration R=0.7. An electric furnace was embedded with ECAP die to regulate the material flow through this die. The temperature of the die was maintained at 450oC during ECAP pressing and the specimens were also preheated at this temperature using another furnace. The ECAP die consistsof two channels intersecting at 90o provided with safe inner and outer corner radius to avoid scaling.The microstructural observations revealed that the deformation was perfectly plastic. The ECAPed and as-received materials were also characterized by tensile tests, micro-hardness tests, and 3-point bend fatigue tests.
Publication Details
Page(s) 435-442
Published Journal: Mehran University Research Journal of Engineering and Technology, Volume: 38, Issue: 2, Year: 2019

Request the full text from PASTIC

References
Jiang , H.,Zhu , Y.T.,Butt , D.P.,Alexandrov , I.V.,Lowe,MaterialsScience,Engineering-A, 2000.Microhardness and Thermal Stability of HPT-Processed Cu”, 290 128 -138
Tan , E.A.,Kibar , A.,Gür , C.H.,MaterialsCharacterization, 2011.“Mechanical and Microstructural Characterization of 6061 Aluminum Alloy Strips Severely Deformed by Dissimilar Channel Angular Pressing”, 62 391 -397
Su , L.,Lu , C.,Tieu , A.K.,Deng , G.,Sun , X., 2013.Ultrafine Grained AA1050/AA6061 Composite Produced by Accumulative Roll Bonding”, Materials Science, 559 345 -351
Zhao , Y.,Guo , H.,Shi , Z.,Yao , Z., 2011.Microstructure Evolution of TA15 Titanium Alloy Subjected to Equal Channel Angular Pressing and Subsequent Annealing at Various Temperatures”,Journal of Materials Processing Technology 211 1364 -1371
Iwahashi , Y.,Horita , Z.,Nemoto , M.,Langdon,ActaMaterialia, 1997.“An Investigation of Microstructural Evolution during Equal-Channel Angular Pressing”, 45 4733 -4741
Segal , V., 1999.Equal Channel Angular Extrusion: From Macromechanics to Structure Formation”, Materials Science, 271 322 -333
Zhu , Y.T.,Low, 2000.Observations and Issues on Mechanisms of Grain Refinement during ECAP Process”, 291 46 -53
Jin , Y.G.,Baek , H.M.,Im,Jeon , B.C., 2011.Continuous ECAP Process Design for Manufacturing a Microstructure-Refined Bolt”, Materials Science, 530 462 -468
Chen , D.C.,Chen , C.P., 2008.Investigation Into Equal Channel Angular Extrusion Process of Billet with Internal Defects”,Journal of Materials Processing Technology 204 419 -424
Ma , K.,Wen , H.,Hu , T.,Topping,Isheim , D.,Seidman , D.N.,ActaMaterialia, 2014.Mechanical Behavior and Strengthening Mechanisms in Ultrafine Grain PrecipitationStrengthened Aluminum Alloy”,[10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] 62 141 -155
Valiev , R.Z.,Murashkin , M.Y.,Bobruk , E.V.,Raa , G.I.B.,MaterialsTransactions, 2009.Grain Refinement and Mechanical Behavior of the Al Alloy, Subjected to the New SPD Technique”, 50 87 -91
Rosochowski , A.,Olejnik , L., 2002.“Numerical and Physical Modelling of Plastic Deformation in 2-Turn Equal Channel Angular Extrusion”,Journal of Materials Processing Technology 125 309 -316
Li , S.,Bourke , M.A.M.,Beyerlein , I.J.,Alexander , D.J.,Clausen , B., 2004.Finite Element Analysis of the Plastic Deformation Zone and Working Load in Equal Channel Angular Extrusion”,Materials Science and EngineeringA 382 217 -236
Gilioli , A.,Manes , A.,Giglio , M., 2014.Numerical Simulation of a Fracture Toughness Test of an Al6061- T6 Aluminium Alloy Using a Ductile Criterion”,Mechanics Research Communications 58 2 -9
Standard-A, 2004.Standard Test Method for Tension Testing of Metallic Materials”, E8M -
Standard-A, 1993.Standard Test Method for Plane Strain Fracture Toughness of Metallic Materials”, E399 -
H.-S.L.-A. Steels, 1990.Properties and Selection: Irons, Steels, and High-Performance Alloys”,ASM International Handbook 1 389 -
Dinda , S.,Kujawski , D., 2004.Correlation and Prediction of Fatigue Crack Growth for Different R-Ratios Using K Max and, 71 1779 -1790
Kujawski , D., 2001.Enhanced Model of Partial Crack Closure for Correlation of R-Ratio Effects in Aluminum Alloys”,International Journal of Fatigue 23 95 -102
Kujawski , D., 2001.A New (AK+K Max) 0.5 Driving Force Parameter for Crack Growth in Aluminum Alloys”,International Journal of Fatigue 23 733 -740
Kujawski , D.,Ellyin , F., 1987.“A Fatigue Crack Growth Model with Load Ratio Effects”, 28 367 -378
0

Citations

0

Downloads

45

Views