No Detail Found!

Effect of Artificial Aging Temperature on Mechanical Properties of 6061 Aluminum Alloy.

Author(s)
MUKESH KUMAR Department of Metallurgy & Materials Engineering, Mehran University of Engineering & Technology, Jamshoro, Pakistan
Muhammad Moazam Baloch Department of Metallurgy & Materials Engineering, Mehran University of Engineering & Technology, Jamshoro, Pakistan
Muhammad Ishaque Abro Department of Metallurgy & Materials Engineering, Mehran University of Engineering & Technology, Jamshoro, Pakistan
Sikandar Ali Memon Department of Metallurgy & Materials Engineering, Mehran University of Engineering & Technology, Jamshoro, Pakistan
ALIDAD CHANDIO Department of Metallurgical Engineering, NED University of Engineering & Technology, Karachi, Pakistan
Abstract
Aluminum alloys have been attracted by several engineering sectors due to their excellent strengthweight ratio and corrosion resistant properties. These are categorized into 1, 2, 3, 4, 5, 6, 7and 8xxx on the basis of alloying elements. Among these 6xxx series contains aluminum-magnesium-silicon as alloying elements and are widely used in extruded products and automotive body panels. The major advantages of these alloys are good corrosion resistance, medium strength, low cost, age hardening response no yield point phenomenon and Ludering. 6xxx series alloys generally have lower formability than other aluminum alloys which restrict their utilization for wide applications. Keeping in view of the shortcomings in the set of mechanical properties of 6xxx series the efforts were made to improve the tensile strength and toughness properties through age hardening. In present study heat treatment cycles were studied for 6061 aluminum alloy. Three different age hardening temperatures 160, 200 and 240oC were selected. The obtained results showed that 17.26, 7.69, and 10.51% improvement in tensile strength, toughness and hardness respectively was achieved with solution treatment at 380oC followed by an aging 240oC. Microstructural study revealed that substantial improvements in the mechanical properties of 6061 aluminum alloy under heat treatment were achieved due to precipitation of Mg2Si secondary phase.
Publication Details
Page(s) 31-36
Published Journal: Mehran University Research Journal of Engineering and Technology, Volume: 38, Issue: 1, Year: 2019

Request the full text from PASTIC

References
Lang, P.,Erwin, P-K., Ahmed, F.,and Ernst, K., “Simulation of the Effect of Composition on the Precipitation in 6xxx Al Alloys During Continuous- Heating DSC”, Journal of Alloys and Compounds, Volume 612, pp. 443-449, 2014
Zoller, H., and Ried, A., “Metallurgical Aspects in Development of Al Mg Si Alloys with a Low Sensitivity to Quenching”, Z Metallkd, Volume 62, pp. 354-358, 2005.
Jastrzebski, Z.D., “The Nature and Properties of Engineering Materials”, John Wiley & Sons, Lafayette College, New York, 1999
Marioara, C.D., Nordmark, H., Anderson, S.J., and Holmestad, R., “Post â-phases and their influences on microstructure and hardness in 6xxx Al-Mg-Si alloys”, Journal of Materials Science, Volume 46, pp. 471-478, 2006.
Edwards, G.A., Stiller, K., Dunlop, G.L., and Couper, M.J., “The Precipitation Sequence in Al-Mg-Si Alloys”, Acta Material, Volume 46, pp. 3898-3904, 1998
Marioara, C.D., Anderson, S.J., Jansen, J., and Zandbergen, H.W., “The Influence of Temperature and Storage Time at RT on Nucleation of the Beta Phase in a 6082 Al-Mg-Si Alloy”, Acta Material, Volume 51, pp. 789-796, 2003.
Yassar, S.R., “Field Transmission Electron Microscopy and Differential Scanning Calorimetry Studies on the Precipitation Sequence in an Al-Mg-Si Alloy: AA6022”, Journal of Materials Research, Volume 20, pp. 2705-2711, 2005
Hand Book “Heat Treating”, ASM International, Materials Park, pp. 841-879, 1991
Kulkarni, A.J., Krishnamurthy, K., Deshmukh, S.P., and Mishra, R.S., “Effect of Particle Size Distribution on Strength of Precipitation-Hardened Alloys”, Journal of Materials Research, Volume 19, No. 9, 2004.
Callister, W.D., “Material Science and Engineering”, John Wiley and Sons, New York, 1997.
Hosford, W.F., “Overview of Tensile Testing, Tensile Testing”, ASM International, Materials Park, pp. 1-24, 1992
Bergsma, S.C., Kassner, M.E., Li, X., and Rosen, R.S., “The Quench Sensitivity of Hot Extruded 6061-T6 and 6069-T6 Aluminum Alloys”, Proceedings of International Conference on Processing and Manufacturing of Advanced Materials, Session A-4, Las Vegas, Nev, USA, December, 2000.
Kuhn, H., and Medlin, D., “ASM Handbook Mechanical Testing and Evaluation”, ASM International, Ohio, USA, 2000
Talabi, S.I., Adeosun, S.O., Alabi, AF., Aremu, I.N., and Abdulkareem, S.,”Effects of Heat Treatment on the Mechanical Properties of Al-4% Ti Alloy”, International Journal of Metals, 2013
Mansourinejad, M., and Mirzakhani, B., “Influence of Sequence of Cold Working and Aging Treatment on Mechanical Behaviour of 6061-AA”, Transactions of Nonferrous Metals Society of China, Volume 22, No. 9, pp. 2072-2079, 2012.
Evren, T., and Bilgehan, O.,”Influence of Heat Treatment on the Mechanical Properties of AA6066 Alloy”, Turkish Journal of Engineering & Environmental Sciences, Volume 31, No. 1, pp. 53, 2007
0

Citations

0

Downloads

59

Views