No Detail Found!

Power speed reduction units for general aviation part 8: casing design for metal direct additive manufacturing

Author(s)
Luca Piancastelli Department of Industrial Engineering, Alma Mater Studiorum University of Bologna,Viale Risorgimento, Bologna,Italy
Eugenio Pezzuti Università di Roma "Tor Vergata", Dip. di Ingegneria dell'Impresa "Mario Lucertini”,Via del Politecnico, Roma,Italy
Stefano Cassani MultiProjecta,Via Casola Canina, Imola (BO),Italy
Abstract
This paper introduces a practical design procedure for Direct Metal Addictive Manufacturing (AM) by Hybrid Selective Laser Sintering or Melting (SLS/SLM). Theoretically AM frees the designer from many design constraints, practically it introduces new problems and it requires a brand new design of the part. Hybrid manufacturing reduces the problems without solving them totally. Supports can be introduced but represent a waste of time during manufacturing and during the post-mill removal. Before a 3D-printed metal part becomes usable, it has already undergone significant postprocessing in the form of CNC milling, hot-hyping, shot-peening or sand-blasting. Powder-bed fusion parts shows a quite rough surface finish. Considering that post-milling will be necessary in any case, surface finish is less important than other issues metal 3D printing. For example, very small cavities form within the part as it is being built. These defects lead to cracks during the part life cycle. Too few power applied by the wiper, too low laser intensity, excessive or inefficient cooling are the most common causes. Geometry of the part, optimized printing pattern and machine parameters are used to address these problems. AM machine operators have to tune their machines for a given material and print job. In the SLS/SLM process, density is achieved with quality powders, optimized build parameters and controlled machine environment. Hot isostatic pressing treatment as a post-process removes the porosity and reveals excessive defect by deforming the part. Residual stress is a result of the printing process. As the powder is melted and cooled, expansion and contraction occur. The residual stress is compressive at the center of the part and tensile at the boundary surfaces. Therefore, thin walled continuous parts are to be preferred. In fact, the classical ribbed structure has several thickness discontinuity requiring continuous adjustment in the build pattern and in laser modulation. To ensure the quality of the part material, the initial layers of the print are removed via CNC milling after the build is complete. Unfortunately, the thermal stress of the substrate will cause the part itself to warp modifying its geometry. Support structures are positioned in the right locations to prevent distortion or warpage. In addition, overhanging surfaces or down-skins faces have poorer surface finish ad are subjected to warping. For this reason, they also need additional supports. For these reasons, the Direct Metal AM part may have a completely different geometry than a cast component. An example of redesigning of a PSRU (Power Speed Reduction Unit) is provided in this paper.
Publication Details
Page(s) 661-669
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 17, Issue: 6, Year: 2022

Request the full text from PASTIC

Keywords
housing, Aircraft, PSRU, direct metal additive manufacturing, helicopter, Transmission, gear drive
References
Piancastelli L.,Frizziero L.,Donnici G.,Ipswich P.O. Box 682 .1819 .The Meredith ramjet: An efficient way to recover the heat wasted in piston engine cooling. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(12) : 5327-5333.
Piancastelli L.,Frizziero L.,Ipswich P.O. Box 682 .1819 .Turbocharging and turbocompounding optimization in automotive racing. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(11) : 2192-2199.
Piancastelli L.,Frizziero L.,Donnici G.,Ipswich P.O. Box 682 .1819 .Turbomatching of small aircraft diesel common rail engines derived from the automotive field. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(1) : 172-178.
Valentini P.P. .2016 .Computer-aided tolerance allocation of compliant ortho-planar spring mechanism. Int. Jou, 53 : 0952-8091.
Pezzuti E. . .Accuracy in fingertip tracking using Leap Motion Controller for interactive virtual applications. Int. Jour. On Interactive Design and Manufacturing, : 1955-2513.
Pezzuti E.,E E. . .Design and interactive simulation of cross-axis compliant pivot using dynamic spline. Int. Jour. On Interactive Design And Manufacturing, 7 : 1955-2513.
Piancastelli L.,Cassani S.,Ipswich P.O. Box 682 .1819 .Maximum peak pressure evaluation of an automotive common rail diesel piston engine head. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(1) : 212-218.
Piancastelli L.,Cassani S.,Ipswich P.O. Box 682 .1819 .Power Speed Reduction Units for General Aviation Part 2: General Design, Optimum Bearing Selection for Propeller Driven Aircrafts with Piston Engines. Asian Research Publishing Network (ARPN). Journal of Engineering and Applied Sciences. ISSN, 6608(2) : 544-550.
Piancastelli L.,Cassani S.,Ipswich P.O. Box 682 .1819 .High Altitude Operations with Piston Engines Power Plant Design Optimization Part V: Nozzle Design and Ramjet General Considerations. Journal of Engineering and Applied Sciences. ISSN, 6608(7) : 2242-2247.
Piancastelli L.,Gardella M.,Cassani S.,Ipswich P.O. Box 682 .1819 .Cooling System Optimization for Light Diesel Helicopters. Journal of Engineering and Applied Sciences. ISSN, 6608(9) : 2803-2808.
Piancastelli L.,Cassani S.,Ipswich P.O. Box 682 .1819 .On The Conversion Of Automotive Engines For General Aviation. Journal of Engineering and Applied Sciences. ISSN, 6608(13) : 4196-4203.
Piancastelli L.,Cassani S.,Ipswich P.O. Box 682 .1819 .Convertiplane Cruise Performance with Contra-Rotating Propeller. Journal of Engineering and Applied Sciences. ISSN, 6608(19) : 5554-5559.
Ceruti A.,Piancastell L. .2016 .Visual Flight Rules Pilots Into Instrumental Meteorological Conditions: a Proposal for a Mobile Application to Increase In-flight Survivability. International Review of Aerospace Engineering (IREASE), 9(5) : .
Piancastelli L.,Cremonini M.,Cassani S.,Calzini F.,Pezzuti E. .2018 .Intake and exhaust position optimization in the cooling duct of diesel helicopters. ARPN Journal of Engineering and Applied Sciences, 13(17) : 811-4819.
Piancastelli L.,Cassani S.,Pezzuti E.,Pompei L. .2018 .Multi-objective optimization of the cooling system of a diesel helicopter. ARPN Journal of Engineering and Applied Sciences, 13(16) : 4610-4616.
Caligiana G.,Liverani A.,Francia D.,Frizziero L.,Donnici G. .2017 .Integrating QFD and TRIZ for innovative design. Journal of Advanced Mechanical Design, Systems and Manufacturing, 11(2) : .
Frizziero L.,Francia D.,Donnici G.,Liverani A.,Caligiana G. .2018 .Sustainable design of open molds with QFD and TRIZ combination. Journal of Industrial and Production Engineering, 1st January, 35(1) : 21-31.
0

Citations

0

Downloads

9

Views