No Detail Found!

Development of static mixer for water treatment and investigation of effect of geometrical parameters on mixing effectiveness

Author(s)
Ashwin Denny Department of Mechanical Engineering and Management, University of Leicester,,United Kingdom
D. S. Robinson Smart Department of Mechanical Engineering, Karunya Institute of Technology and Sciences,Coimbatore,India
Denny C. Kurissingal UTE Desaladora Chennai Operation Y. Mantenimiento,Chennai,India
J. Pradeep Kumar Department of Mechanical Engineering, Karunya Institute of Technology and Sciences,Coimbatore,India
Joses Jenish Smart Manufacturing Engineering,ResMed Corp,United States of America
Abstract
The mixing of liquids and fluids is one of the most significant industrial processes. Static mixers are also known as mixers which are having fewer moving components and are known as motionless mixers. These kinds of mixers are very efficient devices that are very effective and efficient used for mixing both multiphase and single-phase fluids. One of the objectives in using the static mixers is less energy consumption by avoiding complicated and expensive processes. The conventional mixers which are having moving parts such as impellers are subjected to frequent failure due to corrosion and fatigue failures. Hence in this research work, a motionless type static mixing nozzle has been developed. The developed static mixing nozzle consists of Convergent and divergent sections and a spraying nozzle is inserted into the convergent portion to spray the water to be treated. With a gradual increase in the utilization of static mixers in several industrial operations, it is necessary to accomplish higher mixing efficiency. Mixing performance has been enhanced by designing and developing a new type of static mixing nozzle. For investigations purpose, the internal geometry such as convergent angle, throat length, and distance between the spray nozzle potions to the entrance of the throat is kept variable. The spray nozzle position can be adjusted concerning the entrance of the throat by using a threaded portion connected to the convergent nozzle. The main objective of this research is to improve the mixing performance of static mixers by incorporating design modification to the internal geometry. Various geometry of mixing nozzle was selected and the experiments were conducted by varying the position of spraying nozzle from 50 mm to 70 mm, convergent angle (Cone angle) as 20°C to 25°C, and the throat length from 147 mm to 174 mm. During the experiments, the pH value, turbidity, conductivity, and concentration of mixed fluid were measured and analysed. The results of the experiments revealed that the static mixer geometry such as cone angle, throat length, position of spay nozzle can enhance the mixing effectiveness and can be used in water treatment plants.
Publication Details
Page(s) 262-272
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 17, Issue: 3, Year: 2022

Request the full text from PASTIC

Keywords
mixing nozzle, convergent angle, throat length, static mixer
References
Rauline D.,Le Blévec J. M.,Bousquet J.,Tanguy P. A. .2000 .A comparative assessment of the performance of the Kenics and SMX static mixers. Chem. Eng. Res. Des, 78 : 389-396.
Linden P. F.,Simpson J. E. .1986 .Gravity-driven flows in a turbulent fluid. J. Fluid Mech, 172 : 481-497.
Rauline D.,Tanguy P. A.,Le Blévec J. M.,Bousquet J. .1998 .Numerical investigation of the performance of several static mixers. Can. J. Chem. Eng, 76 : 527-535.
Muzzio F. J.,Swanson P. D.,Ottino J. M. .1991 .The statistics of stretching and stirring in chaotic flows. Phys. Fluids A, 3 : 822-834.
Wünsch O.,Böhme G. .2000 .Numerical simulation of 3d viscous fluid flow and convective mixing in a static mixer. Arch. Appl. Mech, 70 : 91-102.
Zalc J. M.,Szalai E. S.,Muzzio F. J.,Jaffer S. .2002 .Characterization of flow and mixing in an SMX static mixer. AIChE J, 48 : 427-436.
Habchi C.,Ghanem A.,Lemenand T.,Valle D. Della,Peerhossaini H. .2018 .Mixing performance in SplitAnd-Recombine Milli-Static Mixers-A numerical analysis. Chem. Eng. Res. Des, 12 : 298-306.
Armbruster S.,Brochard A.,Lölsberg J.,Yüce S.,Wessling M. .2018 .Aerating static mixers prevent fouling. J. Memb. Sci, 10 : 537-546.
Göbel F.,Golshan S.,Norouzi H. R.,Zarghami R.,Mostoufi N. .2019 .Simulation of granular mixing in a static mixer by the discrete element method. Powder Technol, 02 : 171-179.
Lebaz N.,Sheibat-Othman N. .2018 .A population balance model for the prediction of breakage of emulsion droplets in SMX+ static mixers, Chem. , 12 : 625-634.
Soman S. S.,Madhuranthakam C. M. R. .2017 .Effects of internal geometry modifications on the dispersive and distributive mixing in static mixers. Chem. Eng. Process. Process Intensif, 10 : 31-43.
R. van Hout S.,Murugan A.,Mitra B.,Cukurel B. .2021 .Coaxial circular jets-a review. Fluids, 6 : 1-22.
Aissa W. A. .2014 .Effect of throat length on the performance of an air ejector. , : .
J. M. Zalc E. S.,Szalai F. J.,Muzzio F. J. .2003 .Mixing Dynamics in the SMX Static Mixer as a Function of Injection Location and Flow Ratio, Polym. , 43 : 875-890.
Meijer H. E. H.,Singh M. K.,Anderson P. D. .2011 .On the performance of static mixers: A quantitative comparison. Prog. Polym. Sci, 12 : 1333-1349.
0

Citations

0

Downloads

6

Views