No Detail Found!

The optimum process parameter when cutting of thin plate made of stainless steel 316L using CO2 laser

Author(s)
Dwi Sahputra Faculty of Engineering,Universitas Sumatera Utara, Kampus USU, Medan,Indonesia
Armansyah Ginting Department of Mechanical Engineering, Faculty of Engineering,Universitas Sumatera Utara, Kampus USU, Medan,Indonesia
Suprianto Department of Mechanical Engineering, Faculty of Engineering,Universitas Sumatera Utara, Kampus USU, Medan,Indonesia
Zuhrina Masyithah Department of Chemical Engineering, Faculty of Engineering,Universitas Sumatera Utara, Kampus USU, Medan,Indonesia
Abstract
This study investigated the effect of CO2 laser cutting parameters on the quality of 316L stainless steel used for metal mesh implants. The Taguchi method was selected as the design of experiment with three factors: laser power (360480 W), cutting speed (4-6 mm/min), and material thickness (0.3-1 mm). Dimensional deviation and heat-affected zone (HAZ) of the cut were analysed using the Taguchi and Taguchi-Grey Relational Analysis (T-GRA) methods. The results of Taguchi's analysis identified the optimal parameters for minimizing dimensional deviations as 360 W, 5 mm/min, and 0.6 mm, and for HAZ of 480 W, 5 mm/min, and 1 mm. Analysis of variance showed that the power of the laser significantly affected both dimensional deviation (50.49%) and HAZ (19.91%). T-GRA optimization estimates the optimal parameters as 360 W, 4 mm/min, and 0.6 mm, confirmed through validation experiments with a Gray Relational Grade (GRG) of 1,000. The study concluded that laser power was the most important parameter, followed by the cutting speed and the material thickness used, providing a comprehensive optimization strategy for cutting 316L stainless steel lasers for medical implants.
Publication Details
Page(s) 2006-2025
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 20, Issue: 19, Year: 2025

Request the full text from PASTIC

Keywords
CO2 Laser, material thickness, dimension deviation, T-GRA optimization, heat-affected zone (HAZ)
References
P. .2021 .Laser cutting technique: A literature review. Mater. Today Proc, 08 : 2484-2489.
Sifullah A. M.,Nukman Y.,Hassan M. A.,Hossain A. .2016 .Finite element analysis of fusion laser cutting on stainless steel-304. ARPN Journal of Engineering and Applied Sciences, 11 : 181-189.
Palanisamy and Efzan Chockalingam,M. N. E. Chockalingam .2022 .CO2 laser cutting of glass fibre reinforced polymer composite. ARPN Journal of Engineering and Applied Sciences, 17(14) : 1414-1418.
Gunawan Ginting A.,Suprianto Ginting A. .2025 .Cutting of 316L stainless steel for metal mesh implant using CO2 laser cutting: Analysis and optimization. ARPN Journal of Engineering and Applied Sciences, 11(1) : 181-189.
Subramanian S. .2014 .Thermal Modeling of Laser Machining Process. 9. -08- 096532-1, 10 : 00906-7.
Powell J.,Kaplan A. F. H. .2012 .A technical and commercial comparison of fiber laser and CO2 laser cutting. ICALEO 2012 - 31st Int. Congr. Appl. Lasers Electro-Optics, 10 : 277-281.
Parthiban A.,Sathish T.,Chandran S. S.,Venkatesh R.,Vijayan V. .2019 .Optimization of CO2 laser cutting parameters on austenite stainless steel using grey relational analysis. Int. J. Mech. Eng. Technol, 10 : 984-992.
Riveiro A.,Quintero F.,Lusquiños F.,Comesaña R.,Pou J. R. .2010 .Parametric investigation of CO2 laser cutting of 2024-T3 alloy. J. Mater. Process. Technol, 02(9) : 1138-1152.
Radovanovic M.,Madic M. .2011 .Experimental investigations of CO2 laser cut quality: a review. Rev. Tehnol. Neconv, 15(4) : 35.
Pramanik D.,Kuar A. S.,Sarkar S.,Mitra S. .2020 .Optimisation of edge quality on stainless steel 316L using low-power fibre laser beam machining. Adv. Mater. Process. Technol, 1745734(1) : 42-53.
Bertsch1 K. M. .2020 .Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L. Orig. dislocation, Struct. an Addit. Manuf. austenitic Stainl. Steel 316L, 1(713) : 1-32.
[Ronkhorst C. A.,Mayeur J. R.,Livescu V.,Pokharel R.,Gray Brown D. W.,G. T. Brown D. W. .2019 .Structural representation of additively manufactured 316L austenitic stainless steel. Int. J. Plast, 01 : 70-86.
Yilbas B. S.,Davies R.,Yilbas Z. R. .1992 .Study into penetration speed during CO2 laser cutting of stainless steel. Opt. Lasers Eng, 10(92) : 90013-8166.
Orazi L.,Darwish M.,Reggiani B. .2019 .Investigation on the inert gas-assisted laser cutting performances and quality using supersonic nozzles. Metals (Basel), 10(2) : .
Riveiro A. .2019 .Laser cutting: A review on the influence of assist gas. Materials (Basel), 10(1) : .
Bertsch K. M.,Kuehl B.,Thoma D. J. .2020 .Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L. Acta Mater, 07 : 19-33.
Mohd U.,Pandulu G.,Jayaseelan R. .2019 .Strength evaluation of eco-friendly concrete using the Taguchi method. Mater. Today Proc, 11 : 937-947.
Saydam V.,Parsazadeh M.,Radeef M.,Duan M. .2018 .Design and experimental analysis of a helical coil phase change heat exchanger for thermal energy storage. J. Energy Storage, 11 : 9-17.
Sharma A.,Yadava V. .2017 .Experimental analysis of Nd-YAG laser cutting of sheet materials - A review. Opt. Laser Technol, 08 : 264-280.
Elsheikh A. H.,Deng W.,Showaib E. A. W. .2020 .Improving laser cutting quality of polymethylmethacrylate sheet: Experimental investigation and optimization. J. Mater. Res., : .
.2019 .. , 11(2) : 10.
Saydam V.,Parsazadeh M.,Radeef M.,Duan X. .2018 .Design and experimental analysis of a helical coil phase change heat exchanger for thermal energy storage. Journal of Energy Storage, 11 : 9-17.
Datta S.,Mahapatra S. S. .2010 .Modeling, simulation, and parametric optimization of the wire EDM process using response surface methodology coupled with the grey-Taguchi technique. Int. J. Eng. Sci. Technol, 10(5) : 60144.
0

Citations

0

Downloads

29

Views