No Detail Found!

Optimal prediction of al-8112 alloy cutting force via machining using anfis-pso and anfis-ga for a sustainable cutting process

Author(s)
Imhade P. Okokpujie Department of Mechanical and Industrial Engineering Technology, University of Johannesburg, Johannesburg, South Africa;Department of Mechanical and Mechatronics Engineering, Afe Babalola University, Ado Ekiti, Nigeria
Abstract
Cutting force prediction is one of the important responses that is highly considered during the manufacturing process, mostly via computer numerical control machine. Parameters employed in the industry to transform raw materials into finished products, such as the machining parameters, have many challenges during operations. This can lead to high cutting force, which leads to high energy consumption during operations. Therefore, this study focuses on the optimal prediction of the cutting force of aluminium 8112 alloys via machining using ANFIS-PSO and ANFIS-GA for a sustainable cutting process. The experimental data was obtained from a machining experiment with five cutting parameters: cutting speed, helix angle, feed rate, machining length, and depth at five levels. Also, this experiment was carried out in an eco-friendly machining lubricant (TiO2 nano-lubricant), and a dynamometer was used to record the cutting force during operations for every one of the 50 runs of the experiment. The ANFIS-PSO and ANFIS-GA were employed to predict the cutting force with a ratio of training and testing of 35:15. The results show that ANFIS-PSO and the ANFIS-GA predicted the cutting force with 91.98% and 93.98% for the training data of the model and 90.11% and 92.1% for the testing data respectively. The interaction between the five cutting parameters shows that the helix angle and the machining length have a good relationship during the machining process. Also, the results show that the cutting force decreases as the helix angle decreases with the machining length.
Publication Details
Page(s) 1-2
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 20, Issue: 1, Year: 2025

Request the full text from PASTIC

Keywords
Machining, TiO2 nano-lubricant, cutting force, Al8012 alloy, ANFIS-PSO
References
Gupta M. K.,Korkmaz M. E.,Sarıkaya M.,Krolczyk G. M.,Günay M.,Wojciechowski S. .2021 .Cutting forces and temperature measurements in cryogenic assisted turning of AA2024-T351 alloy: An experimentally validated simulation approach. Measurement, 110594 : .
Aydın M.,Köklü U. .2022 .Analysis of cutting forces at different spindle speeds with straight and helical-flute tools for conventional-speed milling incorporating the effect of tool runout. Mechanics Based Design of Structures and Machines, 2125878(2) : 867-893.
Okokpujie I. P.,Tartibu L. K. .2023 .Cutting Fluid and Its Application with Different Delivering Machining Techniques. In Modern Optimization Techniques for Advanced Machining: Heuristic and Metaheuristic Techniques, (7) : 2-39.
Okokpujie I. P.,Tartibu L. K.,Sinebe J. E.,Adeoye A. O.,Akinlabi E. T. .2022 .Comparative study of rheological effects of vegetable oil-lubricant, TiO2, MWCNTs nano-lubricants, and machining parameters' influence on cutting force for sustainable metal cutting process. Lubricants, 10(4) : .
Jain V.,Raj T. .2018 .Prediction of cutting force by using ANFIS. International Journal of System Assurance Engineering and Management, 9 : 1137-1146.
Okokpujie I. P.,Tartibu L. K. .2023 .Cutting Force Optimisation Under ANN and QRCCD. In Modern Optimization Techniques for Advanced Machining: Heuristic and Metaheuristic Techniques, : 10-231.
Surajudeen-Bakinde N. T.,Faruk N.,Popoola S. I.,Salman M. A.,Oloyede A. A.,Olawoyin L. A.,Calafate C. T. .2018 .Path loss predictions for multitransmitter radio propagation in VHF bands using Adaptive Neuro-Fuzzy Inference System. Engineering Science and Technology, an International Journal, 05(4) : 679-691.
Okokpujie I. P.,Tartibu L. K. .2023 .Adaptive Neuro-Fuzzy Inference System for Prediction of Surface Roughness Under Biodegradable Nanolubricant. In Modern Optimization Techniques for Advanced Machining: Heuristic and Metaheuristic Techniques, : 13-311.
Alarifi I. M.,Nguyen H. M.,Bakhtiyari Naderi,Asadi A.,A. A. .2019 .Feasibility of ANFIS-PSO and ANFIS-GA models in predicting thermophysical properties of Al2O3-MWCNT/oil hybrid nanofluid. Materials, 3628(21) : .
Zand J. P.,Katebi J.,Yaghmaei-Sabegh S. .2023 .A hybrid clustering-based type-2 adaptive neuro-fuzzy forecasting model for smart control systems. Expert Systems with Applications, 122445 : .
Zhang H.,Sun B.,Peng W. .2023 .A novel hybrid deep fuzzy model based on gradient descent algorithm with application to time series forecasting. Expert Systems with Applications, 121988 : .
Sowmya R.,Premkumar M.,Jangir P. .2023 .Newton-Raphson-based optimiser: A new populationbased metaheuristic algorithm for continuous optimisation problems. Engineering Applications of Artificial Intelligence, 107532 : .
Okokpujie I. P.,Tartibu L. K. .2023 .Global Machining Prediction and Optimisation. In Modern Optimization Techniques for Advanced Machining: Heuristic and Metaheuristic Techniques, (7) : 4-90.
Chaudhari S.,Thakare A.,Anter A. M. .2023 .PSOGSA: A parallel implementation model for data clustering using new hybrid swarm intelligence and improved machine learning technique. Sustainable Computing: Informatics and Systems, 100953 : .
Mottahedi A.,Sereshki F.,Ataei M. .2018 .Overbreak prediction in underground excavations using hybrid ANFIS-PSO model. Tunnelling and Underground Space Technology, 05 : 1-9.
Qasem S. N.,Ebtehaj I.,H. I. .2017 .Optimising ANFIS for sediment transport in open channels using different evolutionary algorithms. Journal of Applied Research in Water and Wastewater, 4(1) : 290-298.
Marrel A.,Iooss B. .2024 .Probabilistic surrogate modeling by Gaussian process: A review on recent insights in estimation and validation. Reliability Engineering & System Safety, 110120 : .
Assurin S. R.,Mativenga P.,Cooke K.,Sun H.,Field S.,Walker M.,Mortensgaard M. F. .2024 .Establishing cutting conditions for dry drilling of aluminium alloy stack materials. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 238(1-2) : 214-222.
Korkmaz M. E.,Gupta M. K.,Çelik E.,Ross N. S.,Günay M. .2024 .A sustainable cooling/lubrication method focusing on energy consumption and other machining characteristics in high-speed turning of aluminum alloy. Sustainable Materials and Technologies, 40 : .
Okokpujie I. P.,Sinebe J. E.,Tartibu L. K. .2024 .Study of the Effects of Five Different Machining Fluids on the Surface Hardness and Corrosion Behaviour of Al6061 Alloy. Journal of Advanced Research in Applied Sciences and Engineering Technology, 42(2) : 72-88.
Kuo C.,Chen C.,Jiang S.,Chen Y. .2023 .Effects of the tool geometry, cutting and ultrasonic vibration parameters on the cutting forces, tool wear, machined surface integrity and subsurface damages in routing of glass-fibre-reinforced honeycomb cores. Journal of Manufacturing Processes, 08 : 59-75.
Okokpujie I. P.,Tartibu L. K. .2021 .Experimental analysis of cutting force during machining difficult to cut materials under dry, mineral oil, and TiO2 nano-lubricant. Journal of Measurements in Engineering, 22186(4) : 218-230.
Yang K.,Pan J.,Cao Z.,Zhu Y. .2024 .Investigation of the Effect Mechanism of Cutting Sequence on Spiral Milling of CFRP/Ti Laminates Under Ultrasonic-Assisted Conditions. International Journal of Precision Engineering and Manufacturing, : 1-19.
0

Citations

0

Downloads

86

Views