No Detail Found!

An experimental investigation of abrasive jet machining parameters for optimized surface finish of mild steel components

Author(s)
Shishupal Singh CSJM University,Uttar Pradesh,India
Ajeet Pratap Singh CSJM University,Uttar Pradesh,India
Yastuti Rao Gautam CSJM University,Uttar Pradesh,India
Dinesh Singh IET, DSMNR University,Uttar Pradesh,India
Saifullah Khalid Civil Aviation Research Organization,,India
Abstract
Abrasive jet machining is one of the unconventional machining processes that are initiated for alternations of surface characteristics of ductile materials, like mild steel, due to the entrainment of high-velocity abrasive particles. The present experimental investigation deals with the major process parameters of the AJM process, namely air pressure, standoff distance, and time of machining, on the average surface roughness (Ra) of mild steel specimens. Experiments were conducted on the self-developed AJM setup using aluminum oxide abrasive particles of an average size of 50 µm. The pressure of air is changed in three levels, 6, 7, and 8 bars. The standoff distance is taken as 2 mm constant for all the cases. The surface roughness was measured at machining times of 20, 40, and 45 seconds. The presence of the increase of air pressure from 6 to 8 bars applied for all the machining time showed an increasing influence on roughness, although always significant in Ra. For 8 bars of pressure and 45 s of machining, the minimum resulted in 1.39 µm, compared with 3.47-4.02 µm. The rate of decrease in surface roughness is sharp with increasing machining time from 20 to 40 seconds but marginal beyond that. An optimal machining time of 40-45 seconds was identified to obtain a minimum Ra. Capability of AJM as an effective technique to enhance the surface finish of mild steel components, and practical insight of this study is very useful toward optimization of process parameters for attaining the targeted surface quality. The results obtained may assist in expanding the industrial application of AJM toward the finishing of ductile materials in various manufacturing fields.
Publication Details
Page(s) 797-803
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 19, Issue: 13, Year: 2024

Request the full text from PASTIC

Keywords
surface roughness, process optimization, ductile materials, abrasive jet machining, mild steel
References
Melentiev R.,Fang F. R. .2018 .Recent advances and challenges of abrasive jet machining. CIRP Journal of Manufacturing Science and Technology, 22 : 1-20.
Yadav A.,Jain M. L. .2014 .Abrasive jet machining- research review. SSRN Electronic Journal., : .
Jiang M.,Cai J.,Lv Z.,Huang X.,C. X. .2023 .Research progress in abrasive water jet processing technology. Frontiers in Materials, 10 : .
Rao R. V.,Rao P. S. .2019 .Abrasive jet machining process parameters optimization by using the Jaya algorithm. International Journal of Engineering Research and Applications, 9(1) : 24-29.
Yadav A.,Jain M. L. .2018 .A sustainable challenges of abrasive jet machining (AJM): Art of review. International Journal of Engineering Research & Technology. 7, (5) : 1-4.
Venkatesh M. J.,Goh V. C.,Wong T. N.,Lim K. H.,M. J. K. H. .1989 .An empirical study of parameters in abrasive jet machining. International Journal of Machine Tools and Manufacture, 29(4) : .
Rao R. V.,Rao P. S. .2022 .Abrasive jet machining process parameters optimization using the Jaya algorithm. IOP Conference Series: Materials Science and Engineering, 1193 : .
Uthayakumar M.,Khan M. A.,Kumaran S. T.,Slota A.,Zajac A. .2016 .Machinability of nickel-based superalloy by abrasive water jet machining. Materials and Manufacturing Processes, 31(13) : 1733-1739.
Rao R. V.,Rao P. S. .2018 .Abrasive jet machining process parameters optimization using a teaching-learning-based optimization algorithm. International Journal of Mechanical Engineering and Technology, 9(4) : 202-211.
Uthayakumar M.,Marimuthu P.,Muthuraman V.,Jayaseelan V.,Tzotzis A.,Tzounis L.,Panagiotou G. D. .2021 .Investigating the machining performance of abrasive water jet machining on Inconel 718 alloy. , 11 : .
Rao R. V.,Rao P. S. .2018 .Abrasive jet machining process parameters optimization using Jaya algorithm. International Journal of Mechanical and Production Engineering Development, 8(6) : 1-10.
Uthayakumar M.,Marimuthu P.,Muthuraman V.,Jayaseelan V.,Tzotzis A.,Tzounis L.,Panagiotou G. D. .2019 .Investigating the machining performance of abrasive water jet machining on Inconel 718 alloy. Materials Today: Proceedings, 18 : 2125-2130.
Rao R. V.,Rao P. S. . .Abrasive jet machining process parameters optimization using Jaya algorithm. IOSR Journal of Computer Engineering, 20(4) : 84-89.
Rao R. V.,Rao P. S. .2022 .Abrasive jet machining process parameters optimization using Jaya algorithm. Journal of Advanced Manufacturing Systems, 21(4) : 1-10.
Varun R.,Nanjundeswaraswamy T. .2019 .A Literature Review on Parameters Influencing Abrasive Jet Machining and Abrasive Water Jet machining. Journal of Engineering Research and Application, 9(1) : 24-29.
Venkatesan K.,Devendiran S.,Sachin D.,Swaraj J. .2020 .Investigation of machinability characteristics and comparative analysis under different machining conditions for sustainable manufacturing. Measurement, 154 : 107425-107425.
Balasubramaniam R.,Krishnan J.,Ramakrishnan N. .2002 .An experimental study on the abrasive jet deburring of cross-drilled holes. Journal of Materials Processing Technology, 121(2-3) : 360-368.
Uthayakumar M.,Marimuthu P.,Muthuraman V.,Jayaseelan V.,Tzotzis A.,Tzounis L.,Panagiotou G. D. .2019 .Investigating the machining performance of abrasive water jet machining on Inconel 718 alloy. Materials Today: Proceedings, 18 : 2125-2130.
Uthayakumar M.,Marimuthu P.,Muthuraman V.,Jayaseelan V.,Tzotzis A.,Tzounis L.,Panagiotou G. D. .2022 .Investigating the machining performance of abrasive water jet machining on Inconel 718 alloy. Materials Today: Proceedings, 56 : 2125-2130.
A. K. Chaitanya D. K.,Babu K. G.,Kumar K. G. .2020 .Experimental study on surface roughness by using abrasive jet machine. Materials Today: Proceedings, 23 : 453-457.
0

Citations

0

Downloads

46

Views