No Detail Found!

Feni as raw material for stainless steel 316 and its mechanical properties

Author(s)
Sri Endah Susilowati Department of Mechanical Engineering,Universitas Agustus Jakarta, Jakarta,Indonesia
Didit Sumardiyanto Department of Mechanical Engineering,Universitas Agustus Jakarta, Jakarta,Indonesia
Ahmad Fudholi Solar Energy Research Institute, Universiti Kebangsaan Malaysia, Bangi, Selangor, Malaysia; Research Center for Energy Conversion and Conservation, National Research and Innovation Agency (BRIN), Serpong, Indonesia
Abstract
The manufacture of cast stainless steel 316 (SS 316) requires one essential raw material element, pure nickel. The demand for pure nickel is quite high, its price is the highest among other raw materials and it is still being imported. This study aims to utilise local ferronickel (FeNi) as a raw material for stainless steel and determine the effect of the percentage of FeNi usage on the mechanical properties of austenitic SS 316, which is a metal biomaterial widely used as a bone implant. This material is a potential replacement for nickel for stainless steel production. In this study, local FeNi at percentages of 0%, 23%, 45%, or 70% was added to other casting raw materials. The foundry process was carried out, and the samples were subjected to composition, tensile, hardness, and toughness tests. Results showed that all the samples had a chemical composition that met the SS 316 standard, indicating that the FeNi raw material can be used as raw material for SS 316, although impurities were still found at each percentage addition of FeNi. The tensile strength and hardness were still belowthe SS 316 standard but ductility was higher than the SS 316 standard at all percentages of FeNi.
Publication Details
Page(s) 730-739
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 19, Issue: 12, Year: 2024

Request the full text from PASTIC

Keywords
mechanical properties., FeNi, SS 316
References
Sander G.,Cruz V.,Jurg M.,Birbilis N.,Gao X.,Brameld M.,Hutchinson C. .2017 .On the corrosion and metastable pitting characteristics of 316L stainless steel produced by selective laser melting. J. Electrochem. Soc, 164 : C250-C257.
Davis J. R. .1994 .. , : .
Carlton H. D.,Haboub A.,Gallegos G. F.,Parkinson D. Y.,MacDowell A. A. .2016 .Damage evolution and failure mechanisms in additively manufactured stainless steel. Mater. Sci. Eng. A, 651 : 406-414.
Casalino G.,Campanelli S.,Contuzzi N.,Ludovico A. .2015 .Experimental investigation and statistical optimisation of the selective laser melting process of maraging steel. Opt. Laser Technol, 65 : 151-158.
T. D. Ngo A.,Kashani K. T.,Nguyen D.,Hui D. .2018 .Additive manufacturing (3D printing): a review of materials, methods, applications, and challenges. Compos. Part B Eng, 143 : 172-196.
Ettefagh Ali,Hemmasian Ali .2021 .Corrosion performance of additively manufactured stainless steel parts: A review. Additive Manufacturing, 37 : 101689.
Zuquan JIN .2022 .Passivation and depassivation properties of Cr-Mo alloyed corrosionresistant steel in simulated concrete pore solution. Cement and Concrete Composites, 126 : 104375.
Peguet L.,Gaugain A.,Dussart C.,Malki B.,Baroux B. .2012 .Statistical study of the critical pitting temperature of 22-05 duplex stainless steel. Corros. Sci, 60 : 280-283.
Punckt C.,Bolscher M.,Rotermund H.,Mikhailov A.,Organ L.,Budiansky N.,Scully J.,Hudson J. .2004 .The sudden onset of pitting corrosion on stainless steel is a critical phenomenon. Science, 305 : 1133-1136.
Frankel G.,Li T.,Scully J. .2017 .PerspectiveLocalized Corrosion: Passive Film Breakdown vs. Pit Growth Stability. J. Electrochem. Soc, 164 : C180-C181.
Kim E.,Ishtiaq M.,Han J.C.,Ko K.,Bae H.,Sung H.,Kim J.,Seol J. .2021 .Near atomic-scale comparison of passive film on a 17 wt% Cr-added 18 wt% Mn steel. , : .
Tenong F. F. S. B.,Hikmawati D.,Setiawati E. M. .1816 .Characterization of Vickers hardness and corrosion rate of stainless steel-316L coated with hydroxyapatite-polyvinyl alcohol. In Journal of Physics: Conference Series, 1 : 012012.
Walley K. C.,Bajraliu M.,Gonzalez T.,Nazarian A.,Goulet J. A. .2016 .The chronicle of a stainless steel orthopedic implant. The Orthopaedic Journal at Harvard medical school, 17 : 68-74.
Moosbrugger C.,Sanders B. R.,Anton G. J.,Hrivnak N.,Kinson J.,Polakowski C.,Scott W. W.,Cramer D.,Covino B. S. .2003 .ASM handbook. , 13 : .
Gubicza J.,El-Tahawy M.,Huang Y.,Choi H.,Choe H.,J.L. L H. .2016 .Microstructure, phase composition and hardness evolution in 316L stainless steel processed by highpressure torsion. Mater. Sci. Eng. A, 657 : 215-223.
Yusuf S. M.,Nie M.,Chen Y.,Yang S.,Gao N. .2018 .Microstructure and corrosion performance of 316L stainless steel fabricated by selective laser melting and processed through high-pressure torsion. J. Alloy. Compd, 763 : 360-375.
Bevan M. A.,Ameri A.,East D.,Austin D.,Escobedo-Diaz J. .2017 .Mechanical properties and behavior of additive manufactured stainless steel 316L. Characterization of Minerals, : 577-583.
Trelewicz J. R.,Halada G. P.,Donaldson O. K.,Manogharan G. .2016 .Microstructure and corrosion resistance of laser additively manufactured 316L stainless steel. Jom, 68 : 850-859.
Halada G.,Clayton C. .1993 .Comparison of Mo-N and W-N synergism during passivation of stainless steel through x-ray photoelectron spectroscopy and electrochemical analysis. J. Vac. Sci. Technol. A Vac. Surf. Films, 11 : 2342-2347.
Tian H.,Cheng X.,Wang Y.,Dong C.,Li X. .2018 .Effect of Mo on the interaction between α/γ phases of duplex stainless steel. Electrochimica Acta, 267 : 255-268.
Lotfi N. .2018 .Zinc-nickel alloy electrodeposition: Characterization, properties, multilayers and composites. Protection of metals and physical chemistry of surfaces. , 54 : 1102-1140.
Breu C. M.,Cristóbal M. J.,Losada R.,Nóvoa X. R.,Pena G.,Pérez M. C. .2004 .3056 effect transistors. Journal of Applied Physics, 122(17) : 174503.
Ibrahim O. H.,Ibrahim I. S.,Khalifa T. A. F. .2010 .Impact behavior of different stainless steel weldments at low temperatures. Eng Fail Anal, 17 : 1069-76.
Jae-Bong Lee .2006 .Effects of alloying elements, Cr, Mo, and N on repassivation characteristics of stainless steels using the abrading electrode technique. Materials Chemistry and Physics, 99(3) : 224-234.
Cwalina K.,Lutton K. .2019 .Revisiting the effects of molybdenum and tungsten alloying on corrosion behavior of nickel-chromium alloys in aqueous corrosion. Current Opinion in Solid State and Materials Science, 23 : 129-141.
Bocher F.,Huang R.,Scully J. R.,Edward J. R. .2010 .Prediction of critical crevice potentials for Ni-Cr-Mo alloys in simulated crevice solutions as a function of molybdenum content. Corrosion, 66 : 15-055002.
Farhad Ostovan .2021 .On the role of molybdenum on the microstructural, mechanical, and corrosion properties of the GTAW AISI 316 stainless steel weld. Journal of Materials Research and Technology, 13 : 2115-2125.
Di Jiang .2022 .Synergistic improvement of wear and corrosion resistance of CoCrNiMoCB coatings obtained by laser cladding: Role of Mo concentration. Materials & Design, 219 : 110751.
Tae Shik Yoon .2003 .Effects of sintering conditions on the mechanical properties of metal injection molded 316L stainless steel. ISIJ international. 43, : 119-126.
Salak A. .1995 .. , : .
0

Citations

0

Downloads

44

Views