No Detail Found!

Impact energy in heat-treated aluminium alloy 6061 and 7075

Author(s)
H. Zainuddin Faculty of Mechanical Technology and Engineering,Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, Durian Tunggal, Melaka,Malaysia
M.B. Ali Faculty of Industrial and Manufacturing Technology and Engineering,Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, Durian Tunggal, Melaka,Malaysia
Abstract
Instrumented Charpy impact is one of the promising methods to assess the impact energy; toughness and resilience of a material. The test consists of the Charpy machine and instrumentation equipment which is the strain gauge and the data acquisition system. Impact energy evaluations are important to understand the material behaviour subjected to sudden impact loading. Aluminium 7075 has good strength strength-to-weight ratio than aluminium 6061 and hence the AL 7075 is usually used in the aerospace industry, whilst the AL 6061 is commonly used in the automotive industry. The objective of the study is to observe and analyse the impact response of the Aluminium 6061 and 7075 at different heattreated conditions; O-anneal and T6 temper. In addition to the impact energy absorbed value, the impact strain signal is recorded too. Theoretical impact energy is calculated as well based on the information given by the Charpy machine software. Aluminium 7075 exhibits a lower value of impact energy absorbed and a smaller area under the curve compared to Aluminium 6061. The energy absorption capacity for each material grade and heat-treated condition are different from one another. O-anneal aluminium has a lesser energy absorbed value and a smaller area under the curve than the T6 temper aluminium. The outcome reveals that the heat treatment process alters the material microstructure and mechanical properties, whereas in this study the impact energy responses are influenced by these circumstances. Moreover, the chemical composition of the aluminium alloy distinguishes these two grades from one another, thus resulting in different impact responses.
Publication Details
Page(s) 473-478
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 19, Issue: 8, Year: 2024

Request the full text from PASTIC

Keywords
charpy impact, energy absorbed, AL 6061, AL 7075
References
Rassiah K,Megat Ahmad MM,Ali A. .2015 .Ballistic impact performance of the layered and laminated composites: A reviews. Pertanika J Sci. Technol, 23 : 177-185.
Ali MB,Zakaria KA,Abdullah S,Alkhari MR .2015 .Correlation of Impact Energy from Instrumented Charpy Impact. net/AMM.815. 221, 815 : 221-226.
Abdullah NAZ,Sani MSM,Salwani MS,Husain NA,Thin-Walled Struct NA .2020 .A Review on Crashworthiness Studies of Crash Box Structure. , 153 : .
Azrie S. SN,MT H. S.,C. F. H. S. .2017 .Impact Characterisation of Glass Fibre-Reinforced Polymer (GFRP) Type C-600 and E-800 Using a Single Stage Gas Gun (SSGG). Pertanika J Sci Technol, 25 : 303-316.
Alar Ž,Mandić D. .2018 .Comparasion of Impact and Tensile Properties of High-Strength Steel. Metals (Basel), 8 : 1-7.
Kammer C. .2018 .Aluminum and Aluminum Alloys. In: Springer Handbook of Materials Data. Springer Nature Switzerland AG, : 157-193.
Ng C-H,Yahaya SN,Majid AA .2017 .Reviews on aluminum alloy series and its applications. Acad J Sci. Res, 5 : 708-716.
Sastry Sudhir,Kiros YB,Hailu BG,Budarapu F,PR F .2019 .Impact analysis of compressor rotor blades of an aircraft engine. Front Struct Civ Eng, 13 : 505-514.
Yildiz RA. .2022 .Evaluation of fracture toughness and Charpy V-notch test correlations for selected Al alloys. Eur. Mech. Sci, 6 : 1-8.
Kumar Sunil,Londe S,Dilip Kumar N V.,Ibrahim Kittur K,M. K .2021 .Estimation of fracture toughness (KIC) using Charpy impact test for Al6061T6 and Al7075T6 alloys subjected to corrosion. Mater Today Proc, 01 : 2414-2420.
Wu C,Yuan Y,Kamat R. .2020 .A New Approach to Implement High Strength 7075 Aluminum for Automotive Application. MATEC Web Conf, 326 : .
Harrison NR,Luckey SG .2014 .Hot Stamping of a BPillar Outer from High Strength Aluminum Sheet AA7075. SAE Int J Mater Manuf, 7 : 567-573.
Tisza M,Czinege I. .2018 .Comparative study of the application of steels and aluminium in lightweight production of automotive parts. Int. J Light Mater Manuf, 09 : 229-238.
Davis JR. .2001 .Understanding the Basics. , : 351-416.
Poznak A,Freiberg D,Sanders P. .2018 .Automotive Wrought Aluminium Alloys. , : .
Starke EA,Rashed HMMA .2017 .Alloys: Aluminum. , : .
Mallick PK. .2012 .Advanced materials for automotive applications: an overview. Adv. Mater Automot Eng, : 5-27.
Zakaria KA,Idris MIF,Dharmalingam S .2018 .Fatigue Strain Signal Characteristic and Damage of Automobile Suspension System. ARPN J Eng. Appl. Sci, 13 : 221-225.
ASTM . .E8 / E8M-16, Standard Test Methods for Tension Testing of Metallic Materials. , : .
ASTM . .-18, Standard Test Methods for Notched Bar Impact Testing of Metallic Materials. , : .
Benedyk JC. .2010 .Design and Manufacturing for Lightweight Vehicles. Woodhead Publishing Limited, : 79-113.
Muhammad Said N,Ali MB,Zakaria KA .2018 .Correlation of absorb energy with PSD energy and area under strain-time graph. J Adv Res Fluid Mech Therm Sci, 49 : 126-137.
Zakaria KA,Abdullah S,Ghazali MJ S .2013 .Comparative study of fatigue life behaviour of AA6061 and AA7075 alloys under spectrum loadings. Mater Des, 01 : 48-57.
Callister WDJ,Rethwisch DG .2018 .Materials Science and Engineering: An Introduction, 10th Edition. , : .
Shanmughasundaram P,Dahle AK,Engineering Materials .2018 .Heat Treatment of Aluminum Alloys. , : 1-8.
0

Citations

0

Downloads

56

Views