No Detail Found!

Investigating the effect of molasses concentrations on the characterization of evaporation boat waste for crucible materials candidate

Author(s)
R. D. Widodo Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
R. Rusiyanto Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
A. Athoillah Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
R. Setiadi Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
A. Bahatmaka Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
F. B. Darsono Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
D. F. Fitriyana Department of Mechanical Engineering,Universitas Negeri Semarang, Kampus Sekaran, Gunungpati, Semarang,Indonesia
J. P. Siregar Faculty of Mechanical and Automotive Engineering Technology,Universiti Malaysia Pahang, Pekan, Pekan,Malaysia
T. Cionita Faculty of Engineering and Quantity Surveying, INTI International University,Nilai,Malaysia
R. Ismail Department of Mechanical Engineering, Faculty of Engineering, Diponegoro University,Semarang, Jawa Tengah,Indonesia
A. P. Bayuseno Department of Mechanical Engineering, Faculty of Engineering, Diponegoro University,Semarang, Jawa Tengah,Indonesia
A. P. Irawan Faculty of Engineering,Universitas Tarumanagara, Jakarta Barat,Indonesia
NFDS Guterres Department of Mechanical Engineering, Dili Institute of Technology,Ai-meti Laran Street, Dili, Timor-Leste,
Abstract
The crucible is a container wherein metallic materials are melted in order to generate new objects or alloys. Crucibles are typically formed of ceramic, graphite, silicon-carbide, and steel. Until now, there has been no study on the use of evaporation boat waste and molasses for the manufacture of crucibles. This study shows that molasses was used for binding the crucibles production formed from evaporation boats waste. The goal of this research was to ascertain how using molasses affected the properties of the crucible produced. Evaporation boat waste is made into powder (mesh 80) using a hammer mill. Molasses, evaporation boat waste powder and water with a certain concentration are mixed homogeneously using a mixer. The mixed material is put into a mold that has been adjusted to ASTM C1161-18, and then the compaction process is performed (20 MPa) to produce a green body. The resulting green body underwent a 16-hour drying time in an oven set at 100°C. Afterward, it was sintered for 240 minutes at 1150°C. The specimens in this study were characterized using XRD, SEM, density, hardness and 3-point bending tests. The test results show that molasses as a binder in the manufacture of crucible specimens does not result in the formation of a new crystalline phase. 5% molasses produced the best specimens. In specimens with 5% molasses, the density, hardness, flexural strength, and weight percentage (%) crystal phase of BN and TiB2 were 2.25 g/cm3, 61.6 HRA, 49.96 MPa, 67.5%, and 32.5%.
Publication Details
Page(s) 1354-1364
DOI DOI not available
Published Journal: ARPN Journal of Engineering and Applied Sciences, Volume: 18, Issue: 12, Year: 2023

Request the full text from PASTIC

Keywords
molasses, crucible, evaporation boat waste
0

Citations

0

Downloads

64

Views