No Detail Found!

Performance Analysis of 2-methyltetrahydrofuran Blended on Bio- Diesel Engine.

Author(s)
P Ganeshan Department of Mechanical Engineering, VSB Engineering College, Karur, India
V Ragavan Department of Mechanical Engineering, VSB Engineering College, Karur, India
P Raju Department of Mechanical Engineering, VSB Engineering College, Karur, India
S Karthigayan Department of Mechanical Engineering, Christian College of Engineering and Technology, Oddanchatram- 624619, India
M Nimalan Department of Mechanical Engineering, VSB Engineering College, Karur, India
VMathan Raj Department of Mechanical Engineering, VSB Engineering College, Karur, India
SNaveen Prakash Department of Mechanical Engineering, VSB Engineering College, Karur, India
K Praveen Kumar Department of Mechanical Engineering, VSB Engineering College, Karur, India
P Rajkumar Department of Mechanical Engineering, VSB Engineering College, Karur, India
Abstract
Biodiesel nowadays is emerging as an alternative fuel which is a good replacement to the petroleum diesel. Biodiesel is mainly derived from fats and oils by different methods such as dilution, pyrolysis, micro emulsification and transesterification but these days most commercial method used for bio-diesel production is 2methyltetrahydrofuran transesterification. Biodiesel was prepared using transesterification process by optimizing the production parameters such as alcohol to oil molar ratio, catalyst concentration etc. Engine design also plays an important role as if it is improved it reduces fuel consumption and give better performance parameters. In this thesis the main emphasis has been laid on optimum production of biodiesel from neem oil and then using the biodiesel blends with diesel studying the comparative exhaust emission characteristics and engine performance. A four stroke single cylinder compression ignition engine was used to measure performance and emission parameters. Biodiesel (fire point and calorific value) added to the diesel (fire point and calorific value) at Three different volume concentrations i.e. 10, 20, &30 of Biodiesel and to blend the Biodiesel with 2-Methyltetrahydrofuraneto study the emission levels.
Publication Details
Page(s) 50-52
DOI DOI not available
Published Journal: Pakistan Journal of Biotechnology, Volume: 15, Issue: S2, Year: 2018

Request the full text from PASTIC

References
Atul , D.,K.Roblet,A.Avinashkumar, 2012.Production of bio diesel for high FFA neem oil and its performance, emission and combustion characterization in a single cylinder DICI engine,Fuel Processing Technology 97 118 -129
Balaji , G.,M.Cheralathan, 2015.Experimental investigation of antioxidant effect on oxidation stability and emissions in a methyl ester of neem oil fueled DI diesel engine,Renewable Energy 74 910 -916
Canakci , M.,J.Vangerpen, 2001.Biodiesel production from oils and fats with high free fatty acids,American Society of Agricultural Engineers 44 1429 -1436
Canhas , L.,C.Murat,O.Ibrahim,C.Yakup,P.Adnan,M.Sahirsalman, 2008.Performance characteristics of a low heat rejection diesel engine operating with biodiesel,Renewable Energy 33 1709 -1715
Gerhard , K., 2005.Dependence of biodiesel fuel properties on the structure of fatty acid alkyl esters,Fuel Processing Technology 86 1059 -1070
Khandelwal , S.,Y.Rita, 2012.Biodiesel production from non-edible oils: A Review,Journal of Chemical and Pharmaceutical Research 4 4219 -4230
Mustafa , B.,B.Havva, 2008.A critical review of bio-diesel as a vehicular fuel,Energy Conversion and Management 49 2727 -2741
Mathiyazhagan , M.,Ganapathi , A.,Jaganath , B.,Renganayaki , N.,Sasireka , N., 2011.Production of Biodiesel from Non-edible plant oils having high FFA content,International Journal of Chemical and Environmental Engineering 2 119 -122
MazloomShah,Qing-XiangGuo, 2014.Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts,Biomass and Bioenergy 70 225 -229
Ramning , A.M.,S.Dhotepriya,V.N.Ganvir, 2013.Production of Neem Oil Methyl Ester (NOME) from Oscillatory Baffled Reactor,Research Journal of Recent Sciences 2 223 -228
Dharmalingam , S.,P.Marimuthu,K.Raja, 2014.Optimum Setting of Drilling Parameters in Electrochemical Micro Machining Using Grey Relational Analysis,Latin American Applied Research 44 331 -338
Chandrasekaran , K.,P.Marimuthu,K.Raja, 2013.Prediction model for CNC turning on AISI3- 16 with single and multilayered cutting tool using Box Behnken Design,International Journal of Engineering Transactions A: Basics 26 621 -630
SenthilRajan,A.,K.Raja,P.Marimuthu, 2014., Multi basin desalination using biomass heat source and analytical validation using RSM,Energy Conversion and Management 87 359 -366
0

Citations

0

Downloads

83

Views