No Detail Found!

Comparative Study of White Layer Characteristics for Static and Rotating Workpiece during Electric Discharge Machining.

Author(s)
SHAHID MEHMOOD Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
MASOOD SHAH Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
Bakht Bahadur Rana Glass & Ceramics Research Centre, PCSIR, Laboratories Complex, Ferozepur Road, Lahore, Pakistan
Nazeer Ahmed Anjum Department of Mechanical Engineering, University of Engineering & Technology, Taxila, Pakistan
AMIR SULTAN Department of Mechatronics Engineering, University of Engineering & Technology, Taxila, Pakistan
Abstract
EDMed (Electric Discharge Machined) surfaces are unique in their appearance and metallurgical characteristics, which depend on different parameter such as electric parameters, flushing method, and dielectric type. Conventionally, in static workpiece method the EDM (Electric Discharge Machining) is performed by submerging both of the tool and workpiece in dielectric liquid and side flushing is provided by impinging pressurized dielectric liquid into the gap. Another flushing method has been investigated in this study, in which, instead of side flushing the rotation motion is provided to the workpiece. Surface characteristics for both flushing methods are determined and compared in this study. The investigated surface characteristics are: surface roughness, crater size, surface morphology, white layer thickness and composition. These investigations are performed using optical and SEM (Scanning Electron Microscope). Statistical confidence limits are determined for scattered data of surface roughness. It is found that the white layer thickness and surface roughness are directly proportional to discharge current for both flushing methods. The comparison has shown that the side flushing of statics workpiece gives thicker white layer and lower surface finish as compared to the flushing caused by the rotation of workpiece.
Publication Details
Page(s) 819-830
DOI DOI not available
Published Journal: Mehran University Research Journal of Engineering and Technology, Volume: 36, Issue: 4, Year: 2017

Request the full text from PASTIC

References
Torres , A.,Puertas , I.,Luis , C. J.,PrecisionEngineering, 2015.Modelling of Surface Finish, Electrode Wear and Material Removal Rate in Electrical Discharge Machining of Hard-toMachine Alloys”, 40 33 -45
Zhang , Y.,Liu , Y.,Shen , Y.,Ji , R.,Li , Z.,Zheng , C., 2014.Investigation on the Influence of the Dielectrics on the Material Removal Characteristics of EDM”,Journal of Materials Processing Technology 214 1052 -1061
Kojima , A.,Natsu , W.,Kunieda , M., 2008.Spectroscopic Measurement of Arc Plasma Diameter in EDM”,CIRP Annals - Manufacturing Technology 57 203 -207
Srinivasa , A.,Rao , K.R.,Satyanarayana , B., 2016.Effect of Wire EDM Conditions on Generation of Residual Stresses in Machining of Aluminum 2014 T6 Alloy”,Alexandria Engineering Journal 55 1077 -1084
Sim,Song , J.-W.,Hong,Kim,CurrentNanoscience, 2014.Characteristics of Machined Surface Layer of Cemented Carbide by Wire Electrical Discharge Machine”, 10 56 -61
Saleem , M.,Mufti, 2015.Performance Optimization of Electrical Discharge Machining (Die Sinker) for Al6061 via Taguchi Approach, -
Li , L.,Gu , L.,Xi , X.,Zhao , W., 2012.Influence of Flushing on Performance of EDM with Bunched Electrode”,The International Journal of Advanced Manufacturing Technology 58 187 -194
Makenzi , M.,Ikua , B., 2014.“A Review of Flushing Techniques Used in Electrical Discharge Machining”,Proceedings of Sustainable Research and Innovation Conference 162 -165
Soni , J.,Chakraverti, 1994.“Machining Characteristics of Titanium with Rotary Electro-Discharge Machining”,Wear 171 51 -58
Bamberg , E.,Heamawatanachai , S., 2009.Orbital Electrode Actuation to Improve Efficiency of Drilling Micro-Holes by Micro-EDM”,Journal of Materials Processing Technology 209 1826 -1834
Garn , R.,Schubert , A.,Zeidler,PrecisionEngineering, 2011.“Analysis of the Effect of Vibrations on the Micro-EDM Process at the Workpiece Surface”, 35 364 -368
Wang , J,F ., Cheng, G., and Zhao,F., 2012.Debris and Bubble Movements during Electrical Discharge Machining”,International Journal of Machine Tools and Manufacture 58 11 -18
Singh , S.,Maheshwari , S.,Pandey , P.C., 2004.Some Investigations into the Electric Discharge Machining of Hardened Tool Steel Using Different Electrode Materials”,Journal of Materials Processing Technology 149 272 -277
Kunieda , M.,Lauwers , B.,Rajurkar , K.P.,Schumacher , B.M., 2005.Advancing EDM Through Fundamental Insight into the Process”,CIRP Annals - Manufacturing Technology 54 64 -87
Shabgard , M.,Seyedzavvar , M.,Oliaei , S.N.B., 2011.Influence of Input Parameters on the Characteristics of the EDM Process”,Strojniški Vestnik - Journal of Mechanical Engineering 57 689 -696
Arooj , S.,Shah , M.,Sadiq , S.,Jaffery , S.H.I.,Khushnood , S., 2014.Effect of Current in the EDM Machining of Aluminum 6061 T6 and its Effect on the Surface Morphology”,Arabian Journal for Science and Engineering 39 4187 -4199
Mehmood , S.,Pasha , R.A.,Sultan , A., 2015.Effect of Electric Discharge Machining on Material Removal Rate and White Layer Composition”, -
Chakraborty , S.,Dey , V.,Ghosh , S.K.,PrecisionEngineering, 2015.“A Review on the Use of Dielectric Fluids and their Effects in Electrical Discharge Machining Characteristics”, 40 1 -6
KhalajAmineh,S. , Fadaei,Tehrani,A. , and Mohammadi,A., 2013.“Improving the Surface Quality in Wire Electrical Discharge Machined Specimens by Removing the Recast Layer Using Magnetic Abrasive Finishing Method”,The International Journal of Advanced Manufacturing Technology 66 1793 -1803
Ghanem , F.,Fredj , N.B.,Sidhom , H.,Braham , C., 2010.Effects of Finishing Processes on the Fatigue Life Improvements of Electro-Machined Surfaces of Tool Steel”,The International Journal of Advanced Manufacturing Technology 52 583 -595
Soo , S.L.,Antar , M.T.,Aspinwall , D.K.,Sage , C.,Cuttell , M.,Perez , R.,-,-,-6Mo AerospaceAlloy”,ProcediaCIRP, 2013.The Effect of Wire Electrical Discharge Machining on the Fatigue Life of Ti-, 6 216 -220
0

Citations

0

Downloads

123

Views