No Detail Found!

Effect of Electric Discharge Machining on Material Removal Rate and White Layer Composition.

Author(s)
SHAHID MEHMOOD Department of Mechanical Engineering, University of Engineering & Technology Taxila.
Riffat Asim Pasha Department of Mechanical Engineering, University of Engineering & Technology Taxila, Pakistan
AMIR SULTAN Department of Mechatronics Engineering, University of Engineering & Technology Taxila, Pakistan
Abstract
In this study the MRR (Material Removal Rate) of the aerospace grade (2024 T6) aluminum alloy 2024 T6 has been determined with copper electrode and kerosene oil is used as dielectric liquid. Discharge energy is controlled by electric current while keeping Pulse-ON time and Pulse-OFF time as constant. The characteristics of the EDMed (Electric Discharge Machined) surface are discussed. The sub-surface defect due to arcing has been explained. As the surface material of tool electrode and workpiece melts simultaneously and there are chances of the contamination of both surfaces by the contents of each other. Therefore, the EDS (Energy Dispersive Spectroscopy) of the white layer and base material of the workpiece was performed by SEM (Scanning Electron Microscope) at the discharge currents of 3, 6 and 12 amperes. It was conformed that the contamination of the surface of the workpiece material occurred by carbon, copper and oxygen contents. The quantitative analysis of these contents with respect to the discharge current has been presented in this paper.
Publication Details
Page(s) 45-54
DOI DOI not available
Published Journal: Mehran University Research Journal of Engineering and Technology, Volume: 36, Issue: 1, Year: 2017

Request the full text from PASTIC

References
Ho , K.H.,Newman,Cusanelli , G.,Hessler-Wyser , A.,Bobard , F.,Demellayer , R.,Perez , R.,Flükiger,Nos,,2004,Microstructure at Submicron Scale of The White Layer Produced by EDM Technique”,Journal of Materials Processing Technology,149,289-295
Guo, Y.B., Li, W., and Jawahir, I.S., “Surface Integrity Characterization and Prediction in Machining of Hardened and Difficult-to-Machine Alloys: A State-of- Art Research Review and Analysis”, Machining Science and Technology, Volume 13, No. 4, pp. 437-470, USA, December, 2009.
Kunieda, M., Lauwers, B., Rajurkar, K.P., and Schumacher, B.M., “Advancing EDM through Fundamental Insight into the Process”, CIRP Annals -Manufacturing Technology, Volume 54, No. 2, pp. 64-87, Switzerland, 2005.
Dursun, T. and Soutis, C., “Recent Developments in Advanced Aircraft Aluminium Alloys”, Materials & Design, Volume 56, No., pp. 862-871, UK, December, 2014.
Jabbaripour, B., Sadeghi, M.H., Faridvand, S., and Shabgard, M.R., “Investigating the Effects of EDM Parameters on Surface Integrity, MRR and TWR in Machining of Ti–6Al–4V”, Machining Science and Technology, Volume 16, No. 3, pp. 419-444, USA, August, 2012.
Muthuramalingam, T., and Mohan, B., “A Review on Influence of Electrical Process Parameters in EDM Process”, Archives of Civil and Mechanical Engineering, Volume 15, No. 1, pp. 87-94, Poland, January, 2015.
Chakraborty, S., Dey, V., and Ghosh, S.K., “A Review on the Use of Dielectric Fluids and their Effects in Electrical Discharge Machining Characteristics”, Precision Engineering, Volume 40, pp. 1-6, USA, April, 2015.
Andrea Gatto, E.B.A.L.I., “Aluminium Alloys, Theory And Applications”, InTech, Chapter-17, pp. 355-376, UK, February, 2011
Yadav, V., Jain, V.K., and Dixit, P.M., “Thermal Stresses Due to Electrical Discharge Machining”, International Journal of Machine Tools and Manufacture, Volume 42, No. 8, pp. 877-888, UK, March, 2002.
Bojorquez, B., Marloth, R., and Es-Said, O., “Formation of a Crater in the Workpiece on an Electrical Discharge Machine”, Engineering Failure Analysis, Volume 9, No. 1, pp. 93-97, USA, August, 2002
Zhang, Y., Liu, Y., Ji, R., and Cai, B., “Study of The Recast Layer of a Surface Machined by Sinking Electrical Discharge Machining Using Water-in-Oil Emulsion as Dielectric”, Applied Surface Science, Volume 257, No. 14, pp. 5989-5997, Netherlands, January, 2011.
Cusanelli, G., Hessler-Wyser, A., Bobard, F., Demellayer, R., Perez, R., and Flükiger, R., “Microstructure at Submicron Scale of The White Layer Produced by EDM Technique”, Journal of Materials Processing Technology, Volume 149, Nos. 1-3, pp. 289-295, Switzerland, 2004.
Izquierdo, B., Plaza, S., Sánchez, J.A., Pombo, I., and Ortega, N., “Numerical Prediction of Heat Affected Layer in the EDM of Aeronautical Alloys”, Applied Surface Science, Volume 259, No., pp. 780-790, Netherlands, July, 2012.
Ramasawmy, H., and Blunt, L., “Effect of EDM Process Parameters on 3D Surface Topography”, Journal of Materials Processing Technology, Volume 148, No. 2, pp. 155-164, Switzerland, 2004.
Guo, Y.B., and Sahni, J., “A Comparative Study Of Hard Turned And Cylindrically Ground White Layers”, International Journal of Machine Tools and Manufacture, Volume 44, No. 2-3, pp. 135-145, UK, 2004.
Ekmekci, B., “Residual Stresses and White Layer in Electric Discharge Machining (EDM)”, Applied Surface Science, Volume 253, No. 23, pp. 9234-9240, Netherlands, June, 2007.
Kruth, J.P., Stevens, L., Froyen, L., and Lauwers, B.,“Study of the White Layer of a Surface Machined by Die-Sinking Electro-Discharge Machining”, CIRP Annals - Manufacturing Technology, Volume 44, No. 1, pp. 169-172, Switzerland, 1995.
Subramanian, R., Marimuthu, K., and Sakthivel, M., “Study of Crack Formation and Re-Solidified Layer in EDM Process on T90Mn2W50Cr45 Tool Steel”, Materials and Manufacturing Processes, (To be Accepted), USA, 2012.
Lee, H.T., and Tai, T.Y., “Relationship between EDM Parameters and Surface Crack Formation”, Journal of Materials Processing Technology, Volume 142, No. 3, pp. 676-683, Switzerland, October, 2003.
Daneshmand, S., Kahrizi, E.F., Abedi, E., and Abdolhosseini, M.M., “Influence of Machining Parameters on Electro Discharge Machining of NiTi Shape Memory Alloys”, International Journal of Electrochemical Science, Volume 8, No., pp. 3095-3104, Serbia, March, 2013.
Sivam, S.P., Michaelraj, A.L., S, S.K., R.V., and D.D., “Effects of Electrical Parameters, its Interaction and Tool Geometry in Electric Discharge Machining of Titanium Grade 5 Alloy with Graphite Tool”, Proceedings of the Institution of Mechanical Engineers, Part-B, Journal of Engineering Manufacture, Volume 227, No. 1, pp. 119-131, UK, November, 2012.
Tai, T., and Lu, S., “Improving the Fatigue Life of Electro-Discharge-Machined SDK11 Tool Steel via the Suppression of Surface Cracks”, International Journal of Fatigue, Volume 31, No. 3, pp. 433-438, UK, 2009.
Saleem, M.Q., Khan, A.R., and Mufti, N.A., “Performance Optimization of Electrical Discharge Machining (Die Sinker) for Al-6061 via Taguchi Approach”, Mehran University Research Journal of Engineering & Technology, Volume 34, No. 2, pp. 183-195, Pakistan, April, 2015.
Torres, A., Puertas, I., and Luis, C.J., “Modelling of Surface Finish, Electrode Wear and Material Removal Rate in Electrical Discharge Machining of Hard-to-Machine Alloys”, Precision Engineering, Volume 40, pp. 33-45, USA, April, 2015.
0

Citations

0

Downloads

53

Views