No Detail Found!

Design, Modeling, and Thermal Validation of an Electric Resistance Furnace for High-Temperature Applications

Author(s)
Malik Sarmad Zahid Department of Mechanical Engineering, University of Engineering & Technology Mardan, Mardan 23200, Pakistan
Afaque Ahmed Hayat Department of Mechanical Engineering, University of Engineering & Technology Mardan, Mardan 23200, Pakistan
Asad Ullah Department of Mechanical Engineering, University of Engineering & Technology Mardan, Mardan 23200, Pakistan
Arshad Ali Khan Department of Mechanical Engineering, University of Engineering & Technology Peshawar-Nowshera Campus, Nowshera 24100, Pakistan
Afnan Haider Khan Department of Mechanical Engineering, University of Engineering & Technology Mardan, Mardan 23200, Pakistan
Abstract
This paper describes the design, analytical modeling, and numerical thermal analysis of an electric resistance furnace intended to reach 1200°C. The geometry of a hexagonal heating chamber was used because it provides the highest level of effective heating volume and allows the use of commercially available lightweight refractory bricks. The one-dimensional steady-state analytical heat-transfer model and Finite Element Thermal Analysis (FEA) were performed with ANSYS APDL and ANSYS Workbench. The prediction by the analytical model showed an external wall temperature of about 404 K in the uninsulated furnace, which was too high, indicating excessive heat loss and that minute operating temperature conditions were not safe; the numerical results indicated the same temperature of 395 K with an error of 2.22%. This was counteracted by adding a 40 mm thick insulation layer in the form of ceramic fibers, which led to a reduction in the predicted analytical and numerical results of the external surface temperatures to 356 K and 326 K, respectively, and a standard deviation of 8.42. The insulated design exhibited a decreased amount of heat loss by about 45% and greatly enhanced the retention of heat in the heating chamber. The furnace was expected to reach a temperature of 1200°C in the furnace body in a period of one hour in operation, while keeping the exterior body of the furnace close to ambient temperature. The analytical and numerical results are very close and justify the proposed furnace design and prove the effectiveness of ceramic fiber insulation use in the high-temperature electric furnace.
Publication Details
Page(s) 77-99
DOI DOI not available
Published Journal: The Sciencetech, Volume: 7, Issue: 1, Year: 2026

Request the full text from PASTIC

Keywords
Joule heating, Heat Treatment, Melting, Indirect Heating, Heating Chamber, Resistance Furnace
References
Abadi M.M.,Tang H.,M.M. Rashidi H. .2024 .A review of simulation and numerical modeling of electric arc furnace (EAF) and its processes. Heliyon, 10(11) : .
Al-Nasser M. .2021 .Toward a simplified arc impingement model in a direct-current electric Arc Furnace. , 11(9) : 1482.
Assad M.E.H. .2021 .Numerical Investigation of Heat Transfer WaterCooled Roof in an Electric Arc Furnace. Journal of Thermal Engineering, 7(3) : 623-634.
Soultanzadeh Babadi,M. Babadi .2023 .Numerical investigation of nanofluid heat transfer in the wall cooling panels of an electric arc steelmaking furnace. SN Applied Sciences, 5(4) : 99.
Chen W. .2024 .. Numerical Study on Heat Transfer Characteristic of Hot Metal Transportation before EAF Steelmaking Process. Metals, 14(6) : 673.
Du X.,Zhang Z.,S. Zhang, Z. .2025 .Current Status and Prospects of Electric Furnace Scrap Steel Preheating Technology. International Core Journal of Engineering, 11(6) : 348-354.
Ferber N.L. .2022 .Development of an electric arc furnace steel slag-based ceramic material for high temperature thermal energy storage applications. Journal of energy storage, 51 : 104408.
Guney A.,Cakir O. .2025 .Design and Real-Time Control of an Electric Furnace with Three-Dimensional Heating. , 14(3) : 602.
Hussein M.M. .2022 .Modern temperature control of electric furnace in industrial applications based on modified optimization technique. Energies, 15(22) : 8474.
Huzaidi M.N.,Paimin A.N. .2023 .. Improvement of Electric Furnace Heating Function for Use in Aluminium Waste Management. Research and Innovation in Technical and Vocational Education and Training, 3(2) : 112-121.
Hay T. .2021 .Calculation of view factors in electric arc furnace process modeling. , 92(2) : 2000341.
Jawahery S. .2021 .Thermophysical model for online optimization and control of the electric arc furnace. Metals, 11(10) : 1587.
Kishore K.,Sheikh M.N.,Hadi M.N. .2025 .A critical analysis of electric arc furnace (EAF) slag for sustainable geopolymer concrete production. Materials Today Sustainability, 29 : 101064.
Lee J. .2023 .Power Consumption Optimization for Electric Arc Furnace with Time Series Prediction. In PHM Society Asia-Pacific Conference, : .
Li M. .2024 .Numerical simulation of the heating process in a vacuum sintering electric furnace and structural optimization. Scientific Reports, 14(1) : 30905.
Makarov A.N. .2020 .Theory and Practice of Heat Transfer in Electric Arc and Flare Furnaces and Power Plants. World Journal of Engineering and Technology, 8(04) : 739.
Pauna H. .2025 .Hydrogen Direct Reduced Iron Melting in an Electric Arc Furnace: Benefits of In Situ Monitoring. Journal of Sustainable Metallurgy, 11(4) : 4655-4667.
0

Citations

0

Downloads

13

Views