No Detail Found!

Effect of Laser Scanning Speed on the Morphological Properties of CO2 Laser Modified, Wire-arc Sprayed Aluminum Bronze Coatings, Deposited on Aisi-304 Stainless Steel

Author(s)
A. Inam Institute of Metallurgy & Materials Engineering, University of the Punjab, 54590, Lahore, Pakistan
A.M.H. Alvi Institute of Metallurgy & Materials Engineering, University of the Punjab, 54590, Lahore, Pakistan
Misbah-ul-Hassan Institute of Metallurgy & Materials Engineering, University of the Punjab, 54590, Lahore, Pakistan
Inam Ullah Institute of Metallurgy & Materials Engineering, University of the Punjab, 54590, Lahore, Pakistan
H.M.R. Tariq Department of Mechanical Engineering, Incheon National University, Incheon, 22012, Republic of Korea
M. Ishtiaq Institute of Metallurgy & Materials Engineering, University of the Punjab, 54590, Lahore, Pakistan
Abstract
Herein, the effect of laser-scanning speeds on the morphological properties of CO2 laser-modified, wire-arc sprayed aluminum bronze coating was investigated. Firstly, the aluminum bronze coating was deposited on AISI-304 stainless steel by wire-arc spray method. The surface of the deposited coating was then modified, using CO2 laser remelting process under various scanning speeds, ranging from 100-500 mm/min. Scanning electron microscopy revealed that the CO2 laser treatment melted the aluminum bronze coating and the substrate beneath. This melting resulted in a stable, homogeneous alloy of coating and substrate. At CO2 laser scanning speed of 100 mm/min, the coating was deeply diffused into the substrate and formed a coating of 530.13 µm thickness, composed of an alloy coating and substrate. With the increase in CO2 laser scanning speed, a gradual reduction in the thickness of the diffused coating was observed. At the maximum scanning speed of 500 mm/min, a 57% reduction in the diffused coating was observed, resulting in a thickness of 225.21 µm. SEM-EDS validated the diffusion of the aluminum bronze coating into the substrate by exhibiting 33.52 wt% Fe, 41.22 wt% Cu, and 2.39 wt% Al in the newly formed coating. With an increase in CO2 laser scanning speed, the percentage of Fe was reduced whereas the percentage of Cu was increased in alloyed coatings. A maximum of ~11% reduction in Fe percentage and ~18% improvement in Cu percentage were achieved at the highest scanning speed of 500 mm/min, compared to 100 mm/min scanning speed.
Publication Details
Page(s) 9-20
Published Journal: Journal of Pakistan Institute of Chemical Engineers, Volume: 52, Issue: 1, Year: 2024

Request the full text from PASTIC

Keywords
CO2 Laser, 304 Stainless Steel, Surface Lodification, Morphological Properties, Aluminum Bronze Coating
References
Chen J.,Asmussen R. M.,Zagidulin D.,Noel J. J.,Shoesmith D. W. .2013 ."Electrochemical and corrosion behavior of a 304 stainless-steelbased metal alloy wasteform in dilute aqueous environments,". Corrosion Science, 66 : 142-152.
Sun G. F. .2014 ."Microstructure and corrosion characteristics of 304 stainless steel laseralloyed with CrCrB2," Applied Surface Science. , 295 : 94-107.
Xu J.,Wu X. .2013 ."Acoustic emission response of sensitized 304 stainless steel during intergranular corrosion and stress corrosion cracking,". Corrosion Science, 73 : 262-273.
Lorang G.,Da Cunha Belo M.,Simões A. M. P.,Ferreira M. G. S. .1994 ."Chemical Composition of Passive Films on AISI 304 Stainless Steel,". Journal of The Electrochemical Society, 141(12) : 3347.
Jordan L. R.,Betts A. J.,Dahm K. L.,Dearnley P. A.,Wright G. A. .2005 ."Corrosion and passivation mechanism of chromium diboride coatings on stainless steel,". Corrosion Science, 47(5) : 1085-1096.
Ruf R. R.,Tsuei C. C. .1983 ."Extremely high corrosion resistance in amorphous Cr-B alloys,". Journal of Applied Physics, 54(10) : 5705-5710.
Hertzberg R. W.,Hauser F. E. .1977 ."Deformation and fracture mechanics of engineering materials. , : .
M. Li .2020 ."Microstructure and property of Ni/WC/La2O3 coatings by ultrasonic vibration-assisted laser cladding treatment," Optics and Lasers in Engineering. , 125 : 105848.
Guo D.,Kwok C. T.,S. L. I. Chan C. T. .2018 ."Fabrication of stainless steel 316L/TiB2 composite coating via friction surfacing,". Surface and Coatings Technology, 350 : 936-948.
Rao K. V. S.,Girisha K. G.,Jamuna K.,Tejaswini G. C. .2018 ."Erosion Behaviour of HVOF Sprayed SiC-WC-Cr3C2 Multilayer Coating on 304 Stainless Steel,". Materials Today: Proceedings, 5(11) : 24685-24690.
Chen Z.,Yang W.,Yin X.,Chen Y.,Liu Y.,Xu B. .2020 ."Corrosion protection of 304 stainless steel from a smart conducting polypyrrole coating doped with pH-sensitive molybdateloaded TiO2 nanocontainers," Progress in Organic Coatings. , 146 : 105750.
M. A. Almomani M. T.,Hayajneh M. Y. .2019 .AlDaraghmeh, "The corrosion behavior of AISI 304 stainless steel spin coated with ZrO2 - gelatin nanocomposites,". Materials Research Express, 6(9) : 0965c4.
M. Pantoja F.,Velasco J.,Abenojar M. A.,Martinez M. A. .2019 ."Development of superhydrophobic coatings on AISI 304 austenitic stainless steel with different surface pretreatments," Thin Solid Films. , 671 : 22-30.
J . B .2017 .r u z a u d e t a l . , " T h e d e s i g n o f superhydrophobic stainless steel surfaces by controlling nanostructures: a key parameter to reduce the implantation of pathogenic bacteria," Materials Science. , 73 : 40-47.
López A. J.,López M. D.,Utrilla M. V. .2019 ."High temperature corrosion and wear behavior of HVOF-sprayed coating of Al2O3-NiAl on AISI 304 stainless steel,". Surface and Coatings Technology, 359 : 35-46.
Wang B.,Lee S. W. .2000 ."Erosioncorrosion behaviour of HVOF NiAlAl2O3 intermetallicceramic coating,". Wear, 239(1) : 83-90.
Nan Y. .2019 ."Fabrication of Ni3S2/TiO2 photoanode material for 304 stainless steel photocathodic protection under visible light,". Surface and Coatings Technology, 377 : 124935.
Ohko Y.,Saitoh S.,Tatsuma T.,A. T. .2001 .F u j i s h i m a , " P h o t o e l e c t r o c h e m i c a l anticorrosion and self-cleaning effects of a TiO2 coating for type 304 stainless steel,". Journal of the Electrochemical Society, 148(1) : B24.
Yağan A.,Pekmez N. Özçiçek,Yıldız A. .2008 ."Poly(N-ethylaniline) coatings on 304 stainless steel for corrosion protection in aqueous HCl and NaCl solutions,". Electrochimica Acta, 53(5) : 2474-2482.
Kilmartin P. A.,Trier L.,Wright G. A. .2002 ."Corrosion inhibition of polyaniline and poly(omethoxyaniline) on stainless steels,". Synthetic Metals, 131(1) : 99-109.
Hermas A. A.,Nakayama M.,Ogura K. .2005 ."Enrichment of chromium-content in passive layers on stainless steel coated with polyaniline,". Electrochimica Acta, 50(10) : 2001-2007.
Mandal P.,Kiran N. Usha,Chanda U. K.,Pati S.,Roy S. .2021 ."Corrosion performance of graphene oxide coated 304 SS in PEMFC environment,". SN Applied Sciences, 3(7) : 715.
Abdi F.,Savaloni H. . ."Corrosion Inhibition of AISI304 Stainless Steel by Graphen Oxide Coating. , 01 : .
Rajaei V.,Rashtchi H.,Raeissi K.,Shamanian M. .2017 ."The study of Ni-based nanocrystalline and amorphous alloy coatings on AISI 304 stainless steel for PEM fuel cell bipolar plate application,". International Journal of Hydrogen Energy, 42(20) : 14264-14278.
J. Feng M. G. S.,Ferreira R.,Vilar R. .1997 ."Laser cladding of Ni-Cr/Al2O3 composite coatings on AISI 304 stainless steel,". Surface and Coatings Technology, 88(1) : 212-218.
Tian X.,Chen P.,Yang H.,Hao J. .2020 ."Microstructure and Properties of AlCoCrFeNiSi High-Entropy Alloy Coating on AISI 304 Stainless Steel by Laser Cladding,". Journal of Materials Engineering and Performance, 29(1) : 278-288.
C.-H. Hsu ,K.-L. Chen Z.-H.,Lin C.-Y.,Su C.-Y.,C.-K. Lin C.-Y. .2010 ."Bias effects on the tribological behavior of cathodic arc evaporated CrTiAlN coatings on AISI 304 stainless steel," Thin Solid Films. , 518(14) : 3825-3829.
M. Masanta S. M.,Shariff S. M.,Roy Choudhury A. .2011 ."A comparative study of the tribological performances of laser clad TiB2TiCAl2O3 composite coatings on AISI 1020 and AISI 304 substrates,". Wear, 271(7) : 1124-1133.
Qiao Y.,Xu P. .2022 ."Effect of La2O3 on Microstructure and Properties of Laser Cladding SMA Coating on AISI 304 Stainless Steel,". Coatings, 12(7) : 1004.
M. Atapour V.,Rajaei S.,Trasatti M. P.,Casaletto G. L.,Chiarello G. L. .2020 ."Thin Niobium and Niobium Nitride PVD Coatings on AISI 304 Stainless Steel as Bipolar Plates for PEMFCs,". Coatings, 10(9) : 889.
33 J.-H. Huang Z.-E.,Tsai G.-P.,Yu G.-P. .2008 ."Mechanical properties and corrosion resistance of nanocrystalline ZrNxOy coatings on AISI 304 stainless steel by ion plating,". Surface and Coatings Technology, 202(20) : 4992-5000.
Singh H.,Sidhu B. S. .2013 ."Corrosion behavior of plasma sprayed hydroxyapatite and hydroxyapatite-silicon oxide coatings on AISI 304 for biomedical application," Applied Surface Science. , 284 : 811-818.
A. H. Tuthill .1987 .Guidelines for the use of copper alloys in seawater. Nickel Development Institute, : .
Schüssler A.,Exner H. .1993 ."The corrosion of nickel-aluminium bronzes in seawaterI. Protective layer formation and the passivation mechanism,". Corrosion Science, 34(11) : 1793-1802.
Alam S.,Sasaki S.,Shimura H. .2001 ."Friction and wear characteristics of aluminum bronze coatings on steel substrates sprayed by a low pressure plasma technique,". Wear, 248(1) : 75-81.
Liang W.,Xiaolei X.,Jiujun X.,Zukun H. .2000 ."Microstructures and properties of PVD aluminum bronze coatings," Thin Solid Films. , 376(1) : 159-163.
.2006 ."High temperature performance of arc-sprayed aluminum bronze coatings for steel,". Transactions of Nonferrous Metals Society of China, 16(4) : 868-872.
Tao X. P.,Zhang S.,Zhang C. H.,Wu C. L.,Chen J.,Abdullah A. O. .2018 ."Effect of Fe and Ni contents on microstructure and wear resistance of aluminum bronze coatings on 316 stainless steel by laser cladding,". Surface and Coatings Technology, 342 : 76-84.
J. Zhou M.,Yang R.,Wang X.,Pang X. .2017 ."Annealing behavior of aluminum coating prepared by arc spraying on P355NL1 steel,". Surface and Coatings Technology, 330 : 53-60.
Krishnan R.,Dash S.,Kesavamoorthy R.,Rao C. Babu,Tyagi A. K.,Raj B. .2006 ."Laser surface modification and characterization of air plasma sprayed alumina coatings,". Surface and Coatings Technology, 200(8) : 2791-2799.
Ahmadi-Pidani R.,Shoja-Razavi R.,Mozafarinia R.,Jamali H. .2012 ."Improving the thermal shock resistance of plasma sprayed CYSZ thermal barrier coatings by laser surface modification," Optics and Lasers in Engineering. , 50(5) : 780-786.
Ahmadi-Pidani R.,Shoja-Razavi R.,Mozafarinia R.,Jamali H. .2013 ."Laser surface modification of plasma sprayed CYSZ thermal barrier coatings,". Ceramics International, 39(3) : 2473-2480.
P.-C. Tsai J.-H.,Lee J.-H.,C.-L. Chang J.-H. .2007 ."Improving the erosion resistance of plasmasprayed zirconia thermal barrier coatings by laser glazing,". Surface and Coatings Technology, 202(4) : 719-724.
Wang X.,Xiao P.,Schmidt M.,Li L. .2004 ."Laser processing of yttria stabilised zirconia/alumina coatings on Fecralloy substrates,". Surface and Coatings Technology, 187(2) : 370-376.
Chen Y.,Hao H.,Wang W.,Tang W. .2010 ."Analysis of the microstructure and thermal s h o c k r e s i s t a n c e o f l a s e r g l a z e d nanostructured zirconia TBCs," Journal of thermal spray technology. , 19(3) : 558-565.
M. Morks C.,Berndt Y.,Durandet M.,Brandt J.,Wang J. .2010 ."Microscopic observation of laser glazed yttria-stabilized zirconia coatings," Applied Surface Science. , 256(21) : 6213-6218.
D. N.,Serres C.,Demian S.,Costil C.,Langlade C.,Coddet C. .2011 ."Pre/During-/Post-Laser Processes to Enhance the Adhesion and Mechanical Properties of Thermal-Sprayed Coatings with a Reduced Environmental Impact,". Journal of Thermal Spray Technology, 20(4) : 719-735.
J. Chen J.,Li R.,Song L.,Bai J.,Shao C.,Qu C. .2015 ."Effect of the scanning speed on microstructural evolution and wear behaviors of laser cladding NiCrBSi composite coatings,". Optics & Laser Technology, 72 : 86-99.
M. S. Trtica .2004 ."Surface modifications of TiN coating by the pulsed TEA CO2 and KrCl laser," Applied Surface Science. , 225(1) : 362-371.
J. F. Young J. E.,Sipe J. E.,H. M. van Driel J. E. .1984 .Fluence regimes, the role of feedback, and details of the induced topography in germanium," Physical Review B. , 08(4) : 2001-2015.
Sipe J. E.,Young J. F.,Preston J. S.,H. M. van Driel J. S. .1983 ."Laser-induced periodic surface structure. I. Theory," Physical Review B. , 27(01) : 1141-1154.
J. F. Young J. S.,Preston J. S.,H. M. van Driel J. S.,Sipe J. E. .1983 .brass," Physical Review B. , 27(01) : 1155-1172.
H. M. van Driel J. E.,Sipe J. F.,Young J. F. .1982 ."Laser-Induced Periodic Surface Structure on Solids: A Universal Phenomenon," Physical Review Letters. , 12(26) : 1955-1958.
Li X. .2019 ."Manufacturing of Ti3SiC2 lubricated Co-based alloy coatings using laser cladding technology,". Optics & Laser Technology, 114 : 209-215.
Zhang K.,Wang S.,Shang X. .2014 ."Characterization of stainless steel parts by laser metal deposition shaping,". Materials & Design, 55 : 104-119.
Jiao X.,Wang J.,Wang C.,Gong Z.,Pang X.,Xiong S. .2018 ."Effect of laser scanning speed on microstructure and wear properties of T15M cladding coating fabricated by laser cladding technology," Optics and Lasers in Engineering. , 110 : 163-171.
0

Citations

0

Downloads

48

Views