No Detail Found!

Geometry Optimization of Industry Buildings for Energy-Driven Design Development in Bangladesh

Author(s)
Syed Monirul Islam Department of Architecture, Military Institute of Science & Technology,,Bangladesh
Fahmida Chowdhury Department of Architecture, Military Institute of Science & Technology,,Bangladesh
Faysal Bhuiyan Department of Architecture, University of Kansas,,Bangladesh
Masud Ur Rashid Department of Architecture, Southeast University,,Bangladesh
Abstract
Even though the manufacturing industry consumes roughly 54% of total available energy globally, little consideration has been devoted to optimizing energy in the early stages of industry design, particularly in densely populated cities. With the increased demand for green buildings, energy performance has a greater influence on design results. As a result, this paper provides an envelope optimization technique that can assist architects and computational designers in analyzing the environmental performance of various alternatives and developing optimal design solutions, especially for Bangladesh and the building of these regions. First, an existing industrial site in Dhaka, Bangladesh's capital was chosen as a case study, and a hypothetical industry building, as well as its surroundings, were parametrically developed. Then, for the optimization method, the design factors linked to the building envelopes were chosen. Finally, a Multi-objective Optimization (MOO) procedure was utilized for defining performance measures including daylighting, energy and comfort measures, UDI, EUI, and PPD. According to the MOO results, the UDI may be enhanced by 25.286% as compared to the least favorable scenario. Consequently, the EUI may decreased by 38.718 kWh/m2 while the PPD can be increased by 41.78%. The geometric configuration of East, West, North, and South played a significant role when designing the industrial building. According to the analysis, the geometric configuration of a South WWR of 50%, a West WWR of 30%, an East WWR of 70%, and a sill height of 0.75m is the most feasible option. A statistical analysis of design factors and performance measures demonstrated that the window-to-wall ratio, particularly on south walls, has the greatest impact on industrial building design in densely populated areas. The proposed approach is expected to be used by architects and municipal planners to develop design metrics based on simulation results.
Publication Details
Page(s) 119-130
Published Journal: Journal of Daylighting, Volume: 11, Issue: 1, Year: 2024

Request the full text from PASTIC

Keywords
Multi-objective Optimization, Climate-responsive building design, Generative design, Building energy analysis
References
Community .2022 .. Built Environment Project and Asset Management, 12 : 467-485.
Tuhus D. .2010 .Genetic-algorithm based approach to optimize building envelope design for residential buildings. Building and Environment, 45 : 1574-1581.
Lartigue B. .2013 .Multi-Objective Optimization of Building Envelope for Energy Consumption. Indoor and Built Environment, 23 : 70-80.
Conti J.,Holtberg P.,Diefenderfer J.,Westfall L. .2016 ." USDOE Energy Information Administration (EIA. International Energy Outlook 2016 With Projections to, : .
Clark G.,History A Short .2016 .-a-short-history/.. , : .
Ortiz M. A.,Kurvers S. R.,Bluyssen P. M. .2017 .A review of comfort, health, and energy use: Understanding daily energy use and wellbeing for the development of a new approach to study comfort. Energy and Buildings, 152 : 323-335.
Edwards L.,Torcellini P.,Golden P. .2002 .Literature Review of the Effects of Natural Light on Building Occupants, National Renewable Energy Lab. -30769, : .
Chel A.,Kaushik G. .2018 .Renewable energy technologies for sustainable development of energy efficient building. Alexandria Engineering Journal, 57 : 655-669.
Miles J. C.,Sisk G. M.,Moore C. J. .2001 .The conceptual design of commercial buildings using a genetic algorithm. Computers & Structures, 79 : 1583-1592.
Costanzo V.,Evola G.,Marletta L.,Pistone F.,Nascone F. .2018 .Application of Climate Based Daylight Modelling to the Refurbishment of a School Building in Sicily. , 10 : 2653.
Reinhart C. F.,Walkenhorst O. .2001 .Validation of dynamic RADIANCEbased daylight simulations for a test office with external blinds. Energy and Buildings, 33 : 683-697.
Gov .2021 .. Bangladesh National Building Code (BNBC), : .
Nabil A.,Mardaljevic J. .2006 .Useful daylight illuminances: A replacement for daylight factors. Energy and Buildings, 38 : 905-913.
Shahjahan A. .2012 .An Investigation of indoor Thermal Comfort Range for Rural Houses of Dhaka Region, M.S. thesis. , : .
Charles K. E. .2003 ."Fanger's Thermal Comfort and Draught Models," Institute for Research in Construction. , 162 : 1120082.
Ahmed T.,Rahman M. .2012 .Performance Investigation of Building Ventilation System by Calculating Comfort Criteria through HVAC Simulation. IOSR Journal of Mechanical and Civil Engineering, 3 : 07-12.
Davidson S. .2020 .. , : .
EnergyPlus .2020 .. , : .
Aman J. .2017 .Impact of windows for daylighting on thermal comfort in architecture design. , : .
Aman J.,Tabassum N.,Hopfenblatt J.,Kim J. B.,Haque M. O. .2021 .Optimizing Container Housing Units for Informal Settlements- A parametric simulation & visualization workflow for architectural resilience. in 26th International Conference of the Association for Computer-Aided Architectural Design Research in Asia (CAADRIA), : .
.2020 .-whats-window-to-wall-ratio/.. , : .
Holland J. H. .1992 .. , 267 : 66-72.
0

Citations

0

Downloads

49

Views