No Detail Found!

Effect of Initial Grain Size and Microstructure on Tensile Strength of Low Carbon- Manganese Steel.

Author(s)
Shahid Hussain Abro Department of Materials Engineering, Faculty of Chemical and Process Engineering, NED University of Engineering and Technology, Karachi, Pakistan
Abdulaal Zuhayr Khazaal Department of Chemical and Materials Engineering, Northern Border University, Arar, Kingdom of Saudi Arabia,
Muhammad Ali Siddiqui Department of Metallurgical Engineering, Faculty of Chemical and Process Engineering, NED University of Engineering and Technology, Karachi, Pakistan
Abstract
An attempt has been made in this research work to probe the sequel of initial grain size of the steel and its impact on tensile strength. Low carbon-manganese steel in respect of initial grain size and final grain size has been deliberately investigated. Two steel samples having similar chemical composition were austenized at temperatures of 925°C and 1100°C respectively with same holding time in the box furnace followed by quenching. Initial microstructure at 925°C and 1100°C were calculated as 62.34 um and 124.4 um respectively. Just after heat treatment both the samples were prepared for tensile testing as per standard. UT machine was used with a cross head speed of 0.5 mm/min. The raw data obtained from the UT were analyzed stress and strain equations and stress-strain diagram was plotted by using origin software. It was concluded that the sample with initial grain size of 62.34 um showed high elongation curve and large plastic range. The large grain sized samples having initial grain size of 124.4 um, the tensile curve showed a short elongation curve with low plastic range.
Publication Details
Page(s) 132-137
DOI DOI not available
Published Journal: Journal of Applied and Emerging Sciences , Volume: 8, Issue: 2, Year: 2018

Request the full text from PASTIC

References
Ÿ JiangHT,WeiDING,DiTANG,HuangW., 2012.Mechanical property and microstructural characterization of C-Mn-Al-Si hot dip galvanizing TRIP steel,Journal of Iron and Steel Research 19 29 -36
Bouquerel J, Verbeken K, De Cooman BC. (2006). Microstructure-based model for the static mechanical behavior of multiphase steels. Acta Materialia 54(6):1443-1456
Konrad J, Zaefferer S, Raabe D. (2006). Investigation of orientation gradients around a hard Laves particle in a warm-rolled Fe3Al-based alloy using a 3D EBSD-FIB technique. Acta Materialia 54(5):1369-1380
Jing C, Suh DW, Oh CS, Wang Z, Kim SJ. (2007). Effects of phosphorous addition on mechanical properties and retained austenite stability of 0.15 C− 1.5 Mn− 1.5 Al TRIPaided cold rolled steels. Metals and Materials International 13(1):13-19
Suh DW, Park SJ, Kim SJ. (2008). Influence of Cr and Ni on Microstructural Evolution during Heat Treatment of Low-Carbon Transformation Induced Plasticity Steels. Metallurgical and Materials Transactions 39(9): 2015-2019
Chatterjee S, Bhadeshia HKDH. (2007). Transformation induced plasticity assisted steels: stress or strain affected martensitic transformation. Materials Science and Technology 23(9):1101-1104
Sugimoto K. (2007). The Effects of Hot-Forging on Mechanical Properties of Ultra-high strength steel. Journal of ISIJ Int. 47:1357–62
Miller RL. (1972). Ultrafine-grained microstructures and mechanical properties of alloy steels. Metallurgical Transactions 3(4):905-912.
Furukawa T, Huang H, Matsumura O. (1994). Effects of carbon content on mechanical properties of 5% Mn steels exhibiting transformation induced plasticity. Materials science and technology 10(11):964-970
Huang H, Matsumura O, Furukawa T. (1994). Retained austenite in low carbon, manganese steel after inter-critical heat treatment. Materials Science and Technology 10(7):621-626.
Takechi H. (2008). Transformation hardening of steel sheet for automotive applications. JOM 60(12): 22-26.
0

Citations

0

Downloads

46

Views